Probably every active phone user at least once encountered a problem when making calls. So, when dialing a number, the phone may write “Call completed”, after which the dial tone is reset. In the article we will analyze: why you cannot make a call and what smartphone settings you will need to check.
What might be causing the error
So, the essence of the problem is quite simple. When you try to dial a subscriber, the call is dropped, and the phone issues a warning that the call has been completed. Most often, the reset occurs immediately after dialing, but there are situations when there are 1, 2 or 5 beeps, then the connection is disconnected. It is worth noting: this problem manifests itself in all operators (MTS, Beeline, Megafon, Tele2, etc.).
Unfortunately, there are quite a few real reasons why the phone will fail when outgoing. However, it is necessary to highlight the most frequent of them:
- Problem with configuring network types in the phone's firmware.
- Do not disturb mode is on or you have been added to the blocked list.
- The problem is due to the active "Call Forwarding" option.
- A technical problem with the SIM card itself or the slot.
- The problem lies in the firmware itself. This is especially true for custom solutions.
- The bug occurs due to failures in the operation of the communication modules themselves, which is a purely technical problem and is solved in the appropriate service centers.
- You should not exclude a temporary problem in the operation of cellular networks, for which the operator is directly responsible.
Also note that "Call ended" most often pops up on Chinese phones Xiaomi, Huawei, Meizu, BG, Leagoo, HTC, etc.
Checking call settings
Let's immediately discard the moment with the problem of coverage from the operator and the lack of money on your balance. So, the first step is to check all the primary settings that may affect outgoing calls.
- Check to see if Do Not Disturb is active on your phone, or if Airplane or Offline mode is active.
- If you cannot reach a specific number, check if it is blacklisted or blocked. You can find this in the settings of the contact itself.
- There is a moment that your number is blacklisted, so try dialing from another phone.
- Take out the SIM card itself and wipe it, and an extra restart of the phone itself will also not hurt.
Separately, we say that you can still reset restrictions on Xiaomi in the settings of the call book itself. To do this: when dialing, find the three menu bars below and go there:
Set the preferred network type
Very often, users are helped by changing the type of network. For example, from 4G, which often comes by default, to 3G, 2G or dynamic (automatic setting). On different devices, the location of these settings may vary. We will show on the example of Xiaomi (MIUI system).
After that, you can reboot once again and try to see if you can get through. The problem with the initialization of calls in 4G is especially relevant on the now popular Xiaomi and HTC. The latter, when making calls, can switch 4G to 3G and vice versa.
Change network mode
This item also helps a lot, but its complexity may lie in the fact that such network mode settings are often hidden in the engineering menu. This solution is somewhat similar to the previous one and you need to look for this setting in the same “Mobile networks” menu. In the case of my Xiaomi (MIUI 10.3), this setting was hidden like this:
In general, you need to experiment with this item if you are a confident user, because an incorrectly set TD-SCDMA or WCDMA parameter will leave you without mobile Internet.
Redirect Check
In some cases, subscriber numbers may have forwarding, which may block the call on your part. For example, if there is a call forwarding on "no answer", then the call will end after 3-5 rings. Most often this happens if the call forwarding is configured incorrectly or the wrong number is set.
Contact the subscriber and ask him to dial the USSD code: ##002# to cancel any call forwarding on the phone. By the way, you can do the same for yourself. For more information, contact your carrier's support and find out about this option.
Conclusion
If all the above solutions did not work, then you need to experiment with resetting to the factory. A completely deplorable option is also possible - the problem is technical in nature and the network modules of your smartphone will fail. In this case, you need to change the SIM cards and see if the problem remains or goes away. If the phone continues to write "Call completed" - you should contact the service center.
If you have your own tips or life hacks for solving such a failure, please write them in the comments.
I dial any number from the phone, the call is completed, that is, I can’t get through to anyone, I can send messages and got the best answer
Answer from Appear and disappear suddenly[guru]
Try doing this:
We go to the Settings menu, then the Call icon, select General settings, Select a line, put a checkmark on Line 1 (there was a checkmark on Line 2).
There is no "Select line" item in the Settings/Call/General settings menu. The "Send your number" item in the same menu helped: "Set by the network" (it was "Off"). Outgoing calls are on!
As an option, there is no money on the phone (you or your interlocutor).
If there is money and the settings did not help, contact your operator first, and if the problem is not in it, then you will have to diagnose it in the workshop.
Answer from she-wolf[guru]
look in the phone settings or in its profile, it may be worth blocking outgoing calls
Answer from Zhenechka Zhurova[newbie]
You need to turn your phone off and on.
Answer from -
[newbie]
What should I do too?
Answer from Vlad Vetrov[newbie]
phone needs to be rebooted
Answer from Vitya Tolchin[newbie]
And if there is no call setting
Answer from Anna Belyaeva[newbie]
and for some reason I write there is a connection, and when you want to call, it shows either a hung ringing or a network failure
Answer from maxim maxim[newbie]
I have Android 6.0 Reset audio settings helped me in: Settings - Sounds and notifications - press the soft key of the phone - select Reset. Nothing bad will happen. It remains only to set ringtones, vibration responses and that's it.
Answer from Elena Mikhailova[guru]
The main thing is not to manage to immediately bring it into repair, because, in most cases, it’s nothing complicated, and you can clean everything yourself! You can read more about what to do and how to fix it here.
gadget-media.ru/no-dial-tone-android/
Answer from [email protected]@:)
[newbie]
Answer from Valeria Nafikova[newbie]
Settings / other networks / mobile networks / access points look for your operator and everything should work.
Answer from 3 answers[guru]
Hello! Here is a selection of topics with answers to your question: I dial any number from the phone, the call is completed, that is, I can’t get through to anyone, I can send messages
You dialed the number of the person you need, but for some reason, when you call, there are no ringing tones. Familiar? In fact, this is the so-called pattern break. After all, since the advent of automatic telephone communication, the standard procedure for calling a subscriber is as follows - we dial the desired number, after which there are ringing beeps in the handset, which means that the called addressee, at the “other end of the wire”, is making calls on the telephone set. With the advent of mobile communications, this procedure has not changed much, except that cellular customers can subscribe to a service that will replace beeps with pleasant music. But what to do when, having dialed the desired number, you do not hear the usual signals, that is, there are no beeps, and why did this happen ?! Let's figure it out together!
Before proceeding to any action, first I advise you to call the number again. Perhaps it was a single short-term failure and the connection was restored!
Reasons why there are no beeps in the handset
In fact, there may be several reasons for this phenomenon, but the most basic ones, due to which there are no beeps when you call a person, are either communication problems or the telephone set is broken. In addition, a lot depends on what kind of connection you use - fixed wired or mobile.
Cable connection (home phone)
Despite the fact that in recent years the conventional wired telephone has practically lost ground, there are still quite a few people who use it. Basically, these are either elderly people, or some firms and organizations.
If you do not get beeps when calling from your home phone, then first listen to whether there is a beep-buzzer at all when you pick up the handset. Quite often, people pick up the phone and dial a number without checking whether the telephone connection is working at all.
When there is no readiness, this usually indicates a break in the line from the distribution cabinet to the telephone, or problems with the cable from the telephone exchange to the cabinet. The malfunction could have been caused by various earthworks carried out near the telephone line, cable breakage by wounded equipment, flooding of junction boxes and cabinets, etc. Until the fitter restores the line, there will be no connection.
By the way, quite often damage to the line occurs in the apartment. For example, the wire was accidentally broken by the children, the cat gnawed and it rubbed against something.
Mobile communications (cell phone)
When there are no beeps when calling from a mobile phone, then most often this means a failure of the cellular communication caused by the fact that you are in an area of \u200b\u200buncertain signal reception, or there is no coverage of your operator in this place at all. In this case, the message “No signal” appears on the display.
Try redialing the number a few more times. Sometimes rebooting the phone helps.
It also happens that the culprit of the problem is the incorrect operation of the phone itself. For example, some application is installed that blocks incoming calls.
Unfortunately, in cases where there are no beeps when calling due to a breakdown of a cell phone or smartphone, there is no other way out than to carry it in for repair.
If there is no opportunity or do not want to talk, subscribers resort to different methods.
The simplest reason why it is impossible to reach the subscriber is that his phone is turned off, or the subscriber himself is out of the network coverage area.
If the call goes through, but the caller does not pick up the phone, it is possible that he cannot / does not want to talk, or his smartphone is in silent mode, or the person has used the capabilities of his smartphone by selecting the "priority" option. For example, owners of Sony devices have such an opportunity - by adjusting the volume of the smartphone, you can select one of the modes "silent", "priority", "sound". Just the "priority" option allows you to filter calls, skipping only those that are in the address book.
The "black list" formed by the subscriber will not allow unwanted people to get through to him. If only one beep passes during an outgoing call, and then the call is dropped, the caller is probably on such a list; or he hears short beeps, as if the number is busy, or the message "the subscriber's device is turned off or is out of network coverage."
This type of communication is not available to the subscriber. What does this mean? - www.site/all_question/other/2016/April/72499/187718
And a completely different picture, if the outgoing call is dropped immediately, and the caller does not hear a single beep.
In this case, it is possible that the subscriber used the services of a mobile operator and turned off all incoming calls; activated the service "prohibition of receiving calls in roaming". In this case, the subscriber can receive SMS messages (that is, they can reach the subscriber), if he has not disabled them too.
The "call barring" service (the so-called "black list"), not only incoming, but also outgoing, is offered to be connected by all mobile operators.
After the service is activated, you can independently add those numbers that are considered as such to the list for unwanted calls. It is also possible to block an unwanted number permanently.
The inability to reach the subscriber may be due to the fact that he has the iVoiceCallMaster program installed, with the help of which all unnecessary or unwanted numbers are forwarded to a SIM card that simply does not work.
There are cases when you can not get through to the subscriber, because the "blocking of incoming / outgoing calls" is enabled in the settings of his smartphone.
For an iPhone, it helps to enable the "show my number" option in the settings so that calls go through.
If the problem with your smartphone is that it does not miss outgoing calls, you can restart it (it is useful to do this periodically), as well as turn off / on the 3G function (maybe it's a "raw" firmware).
For the Android operating system, a program has long been invented that cuts off unnecessary incoming calls or redirects the caller to voice mail. The program is called Current Caller ID and is suitable not only for smartphones, but also for tablets. To take advantage of this opportunity, the Current Caller ID application must be installed on your gadget.
There is an opinion on the Internet that simply the "black list" option, without specific numbers in it, does not allow you to reach the subscriber, and only when it is turned off, the calls go through, but this is a single opinion that needs to be verified.