Note that after installing the pendulum, the starter cartridge Brother TN will turn into a full-fledged TN-2275 with a print resource of 2600 pages (at 5% print coverage).
The Brother TN Starter Cartridge is typically 700 pages full and runs out fairly quickly. It can be refilled for approximately 2,600 pages (at 5% coverage) using Static Control tonerB2240-100B-OS , cartridge for HL-2132/DCP-7057 can be refilled for 1000 pages(at 5% coverage) Uninet toner.
First of all, you need to remove the protective warranty tape, which is sealed with the cover of the toner hopper:
Now you can open the lid of the hopper with a flathead screwdriver:
Empty the cartridge hopper from waste toner residue:
Using a Phillips screwdriver, you can unscrew the screws:
Now, one by one, remove the two levers (holders) that strengthen the magnetic shaft of the cartridge:
After that, you can start removing the locks from the cartridge. Locks can be easily removed with a flathead screwdriver:
Carefully remove all locks holding the magnetic shaft:
After all the locks are removed, you can remove the magnetic shaft:
Use a toner vacuum cleaner to thoroughly clean the cartridge of toner residue. Be sure to gently clean the edge of the dispense blade from the toner.
After cleaning from the toner, you can install the magnetic shaft back, securing it one by one with locks:
Install the levers in their seats and secure with screws:
Now you can fill the toner can into the cartridge:
Close the lid of the toner hopper, take the cartridge in your hands and slightly rotate the magnetic shaft of the cartridge on both sides so as to evenly distribute the toner over its surface:
Cartridge loaded. Now you need to install the pendulum. To do this, you can use either a kit with a ready-made side cover for TN2235/2275 or for TN2090, or a “native” cartridge cover adapted for installing a flag.
In the pictures below, we will show you how to make your own swingarm side cover (if you have a kit with a ready-made side cover, you can skip the instructions for making it and go directly to the part where the installation of the flag is shown).
Before drilling a seat for a flag, it would be advisable to get rid of the starting tooth on the cover:
Place the cover on the edge of the table and start carefully drilling a hole for the pendulum:
Drill slowly, so as not to accidentally ruin the cover:
Install the spring as shown in the figure:
Pay attention to positionlower gear: the tooth must be set in the position shown in the photo below. The position of the tooth also affects the reset of the page counter. In order for the counter to be reset, both the lower gear and the flag must be correctly installed. above her.
Install the pendulum above the spring:
After installing the flag, put on the drilled cover for fitting, as small grooves will need to be cut on the roof for the teeth of the flag:
Slots can be made with an ordinary clerical knife:
The final step: put the cover back in place and secure with screws. Pay attention to the position of the teeth of the flag - as a result, they should stand exactly this way and not otherwise:
The cartridge is ready to go.
P. S.
The refilled pendulum cartridge should be installed in the turned on printer after all tests have passed and the printer is ready to install the cartridge. This is important because the pendulum of the cartridge must stand strictly in its place, otherwise the gears will turn prematurely and throw the teeth of the flag into the wrong position.
Please note that the checkbox is installed on the cartridge once. In the future, it only needs to be twisted to its original position. The process of refilling the cartridge is not very complicated, compared to typical laser cartridges. HP, Canon, Samsung, Xerox . When refilling, it is very important to thoroughly clean the cartridge of old waste toner, otherwise the printouts may show a dirty background.
All MFP without a chip with Brother TN2235/ TN2275 and TN2090 cartridges it is advantageous to use because of the low cost of refilling the cartridge. The absence of chips is what made Brother printers so attractive to our customers.
Internet shop "IT specialist"
Information provided by Ancom-Ink.ru
Work should be carried out with gloves using special equipment.
The whole cartridge is divided into 2 parts: drum cartridge and toner cartridge. We need a toner cartridge (hereinafter simply a cartridge).
At the end of the cartridge there is a cork fixed with a seal. Carefully remove the seal with a slotted screwdriver, then use the same screwdriver to open the plug.
Thoroughly clean the inside of the cartridge with a special vacuum cleaner. If you don't have a vacuum cleaner, you can gently shake the contents over the bag or trash can by tapping the cartridge all over. After cleaning, pour Brother TN-1075 toner (about 60-70g) into the hole and close the plug.
For correct operation of the cartridge, it is recommended to set the gear-“flag” for resetting printed pages. This is to avoid a message on the display indicating that the toner is empty or that the cartridge has been replaced.
In order to put a "flag" you need to remove the cover on the opposite end of the cartridge. Unscrew the 2 fastening screws and press out the 2 latches with a slotted screwdriver. There is a “foot” on the “flag”, the gear must be placed on a free pin so that the “foot” falls into a special groove. After the gear is on the pin, and the “foot” is in the groove, the gear must be rotated clockwise until it clicks (a click means that the “flag” has engaged with the adjacent gear). Replace the cover. Make sure the lid is latched and level. Secure it with two screws. Repeat these steps if the printer still displays toner or replacement messages. There is a slight difference between the TN-1095 and TN-1075 cartridges: the TN-1095 has a slightly larger flag in diameter.
The "foot" of the flag and the final location of the flag 
Groove under the "foot" of the flag 
Attention! These actions are recommended to be carried out after cleaning the cartridge, but before refilling with toner! If there are “no toner” stripes on the magnetic roller (the black roller is located from edge to edge), then you should clean the doctor blade (do not be alarmed by the name, it is not sharp, this is a formality, because it cleans excess toner from the magnetic roller). First you need to unscrew the 2 screws that secure the blade. Using a slotted screwdriver, pry either end of the blade where the screw was and pull it towards you. Do the same on the other side. After you separate the blade from the cartridge, you can start cleaning. It is best to clean off the “burnt” toner with an old and unnecessary plastic card, and an unnecessary pick from the guitar will do. With light movements with a minimum of applied force (the blade is easily deformed, if it bends, printing defects will appear) scrape off the “burnt” toner. Toner residue can be wiped off with a cloth or soft paper towel. Now the blade needs to be put back. The blade itself must be inserted into the space between the foam pad and the magnetic shaft. "Ears" - the grooves of the blade must be docked with the screw holes, press them and secure with two screws.
The cartridge is ready to go!
Instruction
refilling cartridges Brother LC-980, LC-1100
for Brother MFP: DCP-145C, 163C, 165C, 167C, 185C, 383C, 385C, 387C, 585CW
DCP-6690CW MFC-250C, 290C, 297C, 490CW, 790CW, 990CW,
MFC-5490CN, 5890CN, 6490CW
Attention!!! Avoid long periods of printer downtime with empty cartridges! Doing so may cause ink residue to dry in the print head and block nozzles. In this case, the printer will not print until you clean the print head!
Use only the correct ink for refilling ink cartridges.
1. Prepare necessary tools and materials for refilling: ink, a small screwdriver, a syringe without a needle with a capacity of 10 ml, napkins, rubber gloves.
2. To refill the cartridge, you will need to remove the cap. To do this, use the tip of a screwdriver to pry off the cover from both sides (photo 1).
3. Remove the cover by moving it parallel to the body (photo 2).
Attention! At the same time, 2 metal springs are released and fall out. Do not lose them, they will come in handy when assembling the cartridge.
4. Set the cover and springs aside (photo 3).
5. Put on rubber gloves. Fill the syringe with ink of the required type and color, remove the needle.
6. Press the valve pin with the index finger of your left hand air vent to release air when refilling the cartridge.
7. Insert the tip of the ink syringe into the outlet of the cartridge and inject ink slowly while holding down the air valve pin (photo 4).
8. Refill ink until a drop of ink comes out through the vent valve.
9. Depress the valve (remove your finger) and pull the syringe out of the outlet.
10. To assemble the cartridge, install the springs on the special pins inside the cap (photo 5). Holding the cap with springs vertically, put the rest of the ink bottle on it, making sure that the springs are in place (photo 6).
11. Connect both parts of the cartridge until it clicks. Check the correct fit of the cover on the housing: press the cover - it should spring. If the cover does not spring back, then it is not installed correctly - remove it as described above and reinstall it.
12. Install the cartridge in the printer and run the primary test cycle according to the printer maintenance instructions.
Note: The cartridge has an ink level float, so the printer must detect that the cartridge is full.
Today we will take a closer look step by step instructions on refilling the Brother TN-1075 cartridge with your own hands for beginners, according to which it will be possible to quickly and easily restore the performance of your laser printer.
Looking ahead, we note that in this material we will not consider the process of assembling and disassembling the doctor blade for subsequent cleaning. Since if you use high-quality toner, then the need for this procedure may arise only at 7-10 cycles.
On a note! Refilling the Brother TN-1075 cartridge at the MosToner service center with a free departure of the master within the Moscow Ring Road will cost only.
Also, if you use low-quality toner and often clean the waste ink tank on the TN-1075 cartridge, then even the correct installation of the doctor blade will not protect you from streaks during printing over time.
By quality toner, we mean such brands of coloring powder as TOMOEGAWA, Mitsubishi and other brands.
Tools and Consumables
To refill the Brother TN-1075 cartridge, we need tools and expendable materials, among which:
- 50-60g compatible toner(we recommend TOMOEGAWA or Mitsubishi coloring powder);
- knife, flathead screwdriver or piece of metal plate to pry off the toner hopper cover;
- curly screwdriver;
- toner vacuum cleaner* or miniature brush to remove the remaining toner, but if refilling is performed repeatedly with a certain brand of ink powder, then thorough cleaning can be omitted.
*Carefully! A household vacuum cleaner is not suitable for cleaning the toner hopper, since it does not have a sophisticated filtration system that can prevent the spraying of fine particles that are toxic to the human body.
Instructions: how to refill the cartridge Brother TN-1075?
Carefully follow the instructions for refilling the Brother TN-1075 cartridge.
However, if you experience difficulties at one of the stages practical guide, then until the consumable is finally damaged or the printer is out of order, .
Note! The instruction consists of two parts: toner refills and reset counter.
Refilling the Brother TN-1075 toner cartridge
Step #1. Open the toner hopper cover
Open the toner hopper cover by scooping it out with a knife, flathead screwdriver, or a piece of metal plate.
Step 2: Empty the toner hopper
Clean the toner hopper of any remaining toner using a special vacuum cleaner or a miniature brush.
If refilling is carried out on a regular basis with a particular toner, then a thorough cleaning is not necessary.
Pour 50-60g of toner into the hopper and close it with the appropriate lid.
Reset counter on cartridge Brother TN-1075
If you have at your disposal a TN-1075 starter cartridge that does not have a gear with a reset flag, then the counter must be reset on the printer itself.
Step #1. Remove the cartridge side cover
Unscrew the screws on the side cover of the cartridge on the side where the hole for filling the toner is located. Then carefully remove this cover.
Step #2. Take out the central gear
Take out the central gear, which is located under the reset flag.
Step #3. Set the reset flag to the start position
The gear with the reset flag must be set in the start position.
Change the position of the checkbox to the one shown below.
Step number 4. Put back the central gear
Gently slide the center gear into place, leaving the reset flag stationary.
Step number 5. Install the cartridge side cover
Install the side cover of the cartridge by tightening the screws in the designated places.
That's all, reset Counter Brother TN-1075 produced successfully!
Have you used the instructions for refilling the Brother TN-1075 cartridge, but the printer still refuses to print? Seek help at service center Mosttoner!
At the request of customers, we provide detailed illustrated instructions for refilling starter cartridgesBrotherTN2235, TN2275and TN2090 with the copy counter reset checkbox checked.
So, here are the cartridges for the most profitable printers and MFPs without a chip - Brother DCP-7057, DCP-7060D, DCP-7065DN, MFC-7360N, MFC-7460DN, MFC-7860DW, Brother HL-2132R, HL-2240D, HL-2240DR, HL-2250DNR, HL-2270DW, HL-2280DW Unlike similar models in the line of printers and MFPs HP, Canon, Samsung, Xerox, Brother printers are quite easy to maintain. They use toner cartridges that are easy to refill with toner and print with a longer resource than the above analogues.
Refill Brother cartridges, , you can do it at home with the help of this guide. For refilling you will need: toner, a flag (pendulum) with a spring, a side cover of the cartridge and a nozzle for a toner can (for ease of use). If you don’t have a finished one, then you will also need a 20mm feather drill to make it according to our instructions.
The TN-2235 / TN-2275 and TN-2090 cartridge refill kits differ in toner and reset flags. The refilling algorithm for these cartridges is the same.
Note that after installing the pendulum, the starter cartridge Brother TN will become a full-fledged TN-2275 refillable cartridge/ TN-2275 / TN-2090 .
The Brother TN Starter Cartridge is typically 700 pages full and runs out fairly quickly. It can be refilled for approximately 2,600 pages (at 5% coverage) using Static Control toneror the maximum resource flag. MYou can refill the cartridge and 1000 pages(at 5% coverage) with toner or if you select the minimum resource checkbox. If you have a printer or MFP of the DCP-7057 / HL-2132 series, then the cartridge can be refilled ONLY FOR 1000 pages and no more, because the flag of a larger resource does not work for these models. And, therefore, there is no need to use more than 60 grams of toner at a time.
First of all, you need to remove the protective warranty tape, which is sealed with the cover of the toner hopper:
Now you can open the lid of the hopper with a flathead screwdriver:
Empty the cartridge hopper from waste toner residue:
Using a Phillips screwdriver, you can unscrew the screws:
Now, one by one, remove the two levers (holders) that strengthen the magnetic shaft of the cartridge:
After that, you can start removing the locks from the cartridge. Locks can be easily removed with a flathead screwdriver:
Carefully remove all locks holding the magnetic shaft(developer roller) :
After all the locks are removed, you can remove the magnetic shaft (developer roller):
Use a toner vacuum cleaner to thoroughly clean the cartridge of toner residue. Be sure to gently clean the edge of the dispense blade from the toner.
After cleaning from the toner, you can install the magnetic shaft back, securing it one by one with locks:
Install the levers in their seats and secure with screws:
Now you can fill the toner can into the cartridge:
Close the lid of the toner hopper, take the cartridge in your hands and slightly rotate the magnetic shaft of the cartridge on both sides so as to evenly distribute the toner over its surface:
Cartridge loaded. Now you need to install the pendulum. To do this, you can use either a kit with a ready-made side cover or a “native” cartridge cover adapted for installing a flag.
In the pictures below we will show how to make a pendulum with your own hands (if you have a kit with a ready-made side cover, you can skip the instructions for making it and go directly to the part where the installation of the flag is shown).
Before drilling a seat for a flag, it would be advisable to get rid of the starting tooth on the cover:
Place the cover on the edge of the table and start carefully drilling a hole for the pendulum:
Drill slowly, so as not to accidentally ruin the cover:
Install the spring as shown in the figure:
Pay attention to positionlower gear: the tooth must be set in the position shown in the photo below. The position of the tooth also affects the reset of the page counter. In order for the counter to be reset, both the lower gear and the flag must be correctly installed. above her.
Install the pendulum above the spring:
After installing the flag, put on the drilled cover for fitting, as small grooves will need to be cut on the roof for the teeth of the flag:
.jpg)
Slots can be made with an ordinary clerical knife:
The final step: put the cover back in place and secure with screws. Pay attention to the position of the teeth of the flag - as a result, they should stand exactly this way and not otherwise:
The cartridge is ready to go.
P. S.
The refilled pendulum cartridge should be installed in the turned on printer after all tests have passed and the printer is ready to install the cartridge. This is important because the pendulum of the cartridge must stand strictly in its place, otherwise the gears will turn prematurely and throw the teeth of the flag into the wrong position.
Please note that the checkbox is installed on the cartridge once. In the future, after each refueling, it only needs to be twisted to its original position. The process of refilling the cartridge is not very complicated, compared to typical laser cartridges. HP, Canon, Samsung, Xerox . When refilling, it is very important to thoroughly clean the cartridge of old waste toner, otherwise the printouts may show a dirty background.
All MFP without a chip with Brother TN2235/ TN2275 and TN2090 cartridges it is advantageous to use because of the low cost of refilling the cartridge. The absence of chips is what made Brother printers so attractive to our customers.
Internet shop "IT specialist"