Almost everyone who uses a washing machine is aware of its habit of jumping up and down from its seat during the spin cycle. This article will discuss the causes of the phenomenon and methods for their prevention.

Let's look at the reasons first. They can be divided into two groups:

• factors causing vibration of the washing machine;
• factors that allow a vibrating machine to move across the floor.

Why is the washing machine jumping?

The first cause of strong machine vibrations can be non-dismantled transport bolts. They securely fix the washing machine tank inside the body so as not to damage it during transport. Before starting work, bolts and other fixing elements must be removed. It is strictly forbidden to operate the car with them.

The next cause of washing machine vibration is uneven distribution of things in the tank. If you start the car with an empty tank, it will not vibrate. The same thing will happen if you distribute things perfectly evenly - in an even layer around the entire circumference of the tank. In reality, such a distribution cannot be achieved, even evenly distributed at the beginning, they are mixed during the washing process.

Malfunction of the tank suspension and thrust bearings. Loose counterweight.

The purpose of the system of springs, dampers and a counterweight is to make the natural frequency of the tank much lower than the frequency of its rotation. This reduces the amplitude of oscillations and the magnitude of vibrations transmitted to the machine body.

To better understand the contents of the previous paragraph, remember: at the beginning of the spin cycle, the body of the loaded machine sways more, and then with an increase in the rotation speed of the tank, the sway turns into a small tremor or, with the correct distribution of the laundry, practically disappears.

Rock the tank - after that it should make no more than one oscillation and stop. Otherwise, the shock absorbers are faulty, they must be replaced.

Open the casing of the machine, inspect the elastic elements - metal should not have deformations, rubber - tears and cracks. Defective parts - for replacement! Check the counterweight mounting - if loose, tighten the nuts.

Bad bearings. When the machine is running, there should be no creaks or knocks. Turn the tank by hand, shake it from side to side. If you find a creak or beating, replace the defective parts.

Proper installation of the washing machine

First requirement for installation - a horizontal floor. When not level, the vibrating machine will slide in the direction of the slope. If the floor is not ideal, you need to build some kind of podium that creates a horizontal surface for the car. At the same time, he himself should not slide on the floor surface.

Second requirement- the horizontality of the machine itself. Or verticality. It depends on what is chosen as a criterion: the upper plane must be strictly horizontal, any side edge must be vertical.

Why is this needed? With the most careful distribution of things, they will move during the washing process and create a beating when the tank rotates quickly. In uneven standing car the beats will deviate from the calculated ones and, as a result of an uneven load on the supports, can cause displacement.

Is the impact of the deviation significant? It is better not to analyze, but simply to put the car on the level. It's not such a complicated operation.

How to level a car? What is needed to adjust?

Before starting work, prepare a level about 1 meter long. No longer needed. If there is no such long one, we will take what is. But keep in mind that the shorter the level, the less accurate.

You will also need two open end wrenches. The size must match the adjusting nuts on the feet of the machine.

Step-by-step instructions for installing a washing machine

Checking the levelness of the platform on which the device will stand. Actually, the horizontality of not the entire site is important, but the plane passing through the patches on which the legs of the machine will rest.

With a level, we check the horizontalness of the site along both diagonals. If horizontality is observed here, we check along two adjacent sides. If everything is in order here, we put the car with its legs on the checked sites. If the floor is not horizontal in any direction, we put stands on low places, achieving horizontality in all directions.

Stands can be made from any flat and hard material. It is recommended to stick a thin sheet of rubber on the side in contact with the floor. His appointment will be discussed below.

Now we put on the platform or on stands washing machine. By adjusting the height of the legs, we achieve the horizontality of the upper surface. We check the correctness of the vertical installation of the side ribs.

If everything is fine, we tighten the locknuts on the adjusting screws of the legs and once again check if the verticality-horizontality has not been violated during locking.

Now try to shake the car left and right and diagonally. If it does not sway - not almost, but does not sway at all - it means that the machine is set correctly.

But there is one more nuance. As already noted, it is almost impossible to completely eliminate vibrations, so there is always the possibility that the washing machine will leave its rightful place.

Remember, a sheet of rubber was glued to the footrests? This is so that with small vibrations they do not slip on the floor and prevent the car from moving.

Find a rectangular sheet of rubber 1–1.5 cm thick, and about 5 cm larger than the size of the car. The hardness should be such that the legs crush it by about half the thickness. Put it on a horizontal surface under the car, and the probability of leaving will be reduced to zero.

Tips for operating the machine to reduce vibration.

Do not overload the machine. The suspension system is designed to work with a certain load. Exceeding will lead to excessive vibrations, and in the long term to premature failure of nodes.

Before starting, distribute the items evenly around the circumference of the drum. There are machines that can do this on their own, but still help them - artificial intelligence is not yet so smart.

If your machine is a top-loading machine, you can hold something heavy on it, such as a laundry basket. This will increase vibration resistance.

Place the machine at least 5 cm away from the walls so that in case of emergency it does not damage them and itself.

Conclusion

At the end, we briefly list what was said in the article:

• Do not forget Remove shipping bolts;
• The car must be on horizontal surfaces;
• The car must be strictly vertically;
• Place a rubber mat under the legs;
• Evenly distribute things around the circumference of the drum;
• Don't overload car;
• Provide a gap between the wall and the machine at least 5 cm;
• Attention! Never use a damaged machine. If an elastic element breaks on the go or a bearing shatters, the breakdown can reach such proportions that the extra washed shirt turns out to be golden.

From correct installation washing machine- the machine depends on the duration of its service life. And if we look into her passport, we will find many requirements there. For example, it describes how to adjust the legs of the washing machine and how to properly connect it to the mains. Many users may ask - why adjust the legs at all? What does it affect?

As part of this review, we will consider all the most important points regarding the adjustment of the position of the washing machine, as well as discuss the intricacies of the installation process.

Why Proper Leg Adjustment Is Important

Adjusting the legs of the washing machine allows you to give the machine stability. The drum of the machine, rotating even at low speed, creates serious vibrations resulting from uneven distribution of laundry. For the laundry itself, they are absolutely harmless, but the components of the washing machine begin to wear out faster.

Vibrations are a serious threat to any household appliances.. Under its influence, screws, self-tapping screws and other types of fastening loosen up, plastic weakens. Due to vibrations, malfunctions often occur due to damage to the plastic tank, as a result of which it can burst - the water that spills out of it will flood the neighbors from below. And all this could have been avoided if the legs of the washing machine were adjusted in height.

An improperly adjusted machine breaks not only itself. When subjected to vibrations, it may move and damage surrounding objects. Most of the complaints of users are due to the fact that their cars literally “jump” around the bathroom. And few people can figure out that you just need to adjust the legs and give the machine a strictly horizontal position. In addition to vibrations, a trembling machine will make noise that disturbs others.

See what we get as a result of incorrect adjustment:

• A washing machine bouncing around in the bathroom;
• Tanks cracked from vibrations;
• Tiled tiles that have fallen out from accidental impacts on the walls;
• Broken bearings inside the washing machine.

If you want to prolong the life of your washing machine, install it correctly and we will gladly help you with this.

How to adjust the washing machine yourself

Did the store employees tell you that the machine must be installed by a master? Give it up - by following our instructions, you can install and adjust it yourself. The most important thing we need to do is to properly adjust the legs of the washing machine. From the tools we need the most common building level.

The first step is to choose the installation location. It is desirable that there be a concrete floor with good stability. AT individual cases a separate concrete screed is created under the machine so that it stands on a solid foundation (this applies to houses and apartments with wooden floors).

As soon as the platform for the machine is ready, we install it - we simply put it on the selected base and connect it to the water supply, sewerage and electrical networks. Make sure that the body of the device does not pinch the hoses going to the communications. By adjusting the height of the legs, we bring the car into such a state that it does not sway - we achieve a visually correct position. Accordingly, that leg is twisted, in which direction the body collapses when it is swinging.

Rotating clockwise, the legs screw down and become shorter. If you start twisting the legs in the opposite direction, they will become longer. What do we need to do with these legs in the end?

Having set the building level parallel to the front wall, you need to adjust the front legs so that the air bubble is exactly in the middle. This will indicate that the front end is level. After that, we rearrange the level parallel to the side wall and do the same operation with the rear legs. In this case, you need to ensure that the machine is level and does not sway from the side. The end result should be a position where the body of the machine is stable, and the level shows a strictly horizontal position (both front and side).

As soon as we achieve the correct position of the washing machine at its installation site, we can proceed to a test wash. If during washing (especially during the acceleration of the drum) small vibrations are observed, then this is considered normal. The main thing is that the washing machine does not budge, trying to "jump" to the side.

Some specialists can install the washing machine using a glass of water standing on the top cover, but the accuracy building level somewhat higher.

What else you need to know about installing a washing machine

Now we know how to twist the legs of the washing machine and achieve its stable position. But its installation will require compliance a number of additional recommendations:

• Always connect water through a separate tie-in with your own tap - in case of a leak, you can quickly turn off the water;
• Level drain hose(in height) should not exceed the norm - look at the passport and find out to what height the drain hose can be raised;
• Do not connect the washing machine through extension cords - make a separate outlet for it and equip it with a circuit breaker;
• Do not squash the inlet and drain hoses to avoid damage;
• Do not place any heavy or fragile objects and equipment on top of the machine - vibrations can cause them to fall and cause injury;
• When installing the washing machine, do not forget to unscrew the shipping screwslocated on the back cover of the case - they are responsible for the safe transportation of the washing machine, and must be removed during operation.

Having fulfilled all the requirements and having installed the machine according to the building level, you can safely proceed to washing. And all this, mind you, we did without the help of a master who would do the same, but for money.

Connecting a washing machine with your own hands should begin by studying the instructions for it. If any errors are made in this process, this may lead to the inoperability of the device. Since a washing machine is an expensive thing, everything must be done carefully and according to the rules. This will ensure its reliable operation and long service life.

Place for installation

When answering the question of where it is better to install a washing machine, one should be guided by the obvious fact - the place should be near water pipes so that water can flow in and out easily. Bath, kitchen or hallway are traditional places to install a washing machine. The right room should be chosen based on the space available there.

Options for installing a washing machine in the kitchen Options for installing a washing machine in the bathroom
Options for installing a washing machine in the hallway

Preparing for installation

Before you install the washing machine, you must unpack it and remove the shipping bolts and fasteners. These elements are used to ensure that the moving parts of the machine do not dangle from side to side during transportation.

If you forget to remove the transport fasteners and turn on the machine, it will soon fail. And the manufacturer's warranty will no longer apply.

Holes from fasteners are closed with social plastic plugs.

Be sure to remove the transport bolts before installation.

Sewer connection

The next step in the instructions for installing the washing machine is to connect to the sewer. This is necessary in order to drain water from it.

Depending on the design, draining can be done in different ways. The easiest option is to pour the water directly into the tub or kitchen sink. To do this, washing machines are equipped with a special hook on the hose, which is attached to the side of the bathtub or sink.

A more convenient way is to connect the drain to the siphon of the bath or sink. This will require a special outlet. Or you can organize a drain from the washing machine directly into the sewer.

If the washing machine is drained into the sewer, it is necessary to create a bend for the water seal (as the siphon bends), otherwise unpleasant odors will enter the tank. The bend should be lower than the tank of the machine. Therefore, sometimes you have to put it on stands or shelves.

Connecting the washing machine to the drain through the siphon

Water connection

Before you install the washing machine, you should purchase tees that are used to supply water. Sometimes both hot and cold water is supplied, so two tees are needed. In addition, you will need valves to shut off the water when the machine is not in use.

To extend the life of the washing machine, when installing it, it is necessary to install filters in the water supply system that will protect the tank from contamination.

Connecting water to the washing machine through tees.

alignment

Then the washing machine is leveled. Since the floors in the house can be uneven, you need to level the machine using the rotating legs.

If the installation of the washing machine is uneven, it will vibrate, which will create unnecessary noise, as well as lead to wear of parts.

After installing the washing machine, it should not tilt under pressure on each of its four corners.

The washing machine is leveled by adjusting the feet.

Checking the correct installation

The washing machine has been installed correctly if:

• The tank is filled and emptied not too long;
• No leaks;
• The drum rotates without excessive noise;
• Water heats up 5-7 minutes after it stops flowing.

How to install a washing machine with your own hands.

Today I urgently needed knowledge about installing a washing machine with program management. Found a great article online. The author talks in detail and clearly about such difficult things for beginners. I read it with pleasure, now I will make sure that the installation is successful, in accordance with the points outlined from the experience of knowledgeable people. Thank you for the article!

This article will answer all questions regarding self-installation of a washing machine. After reading it, you will learn: how to choose and prepare a place for installation, how to connect it to the water supply, sewerage and electricity, how to maintain a guarantee, as well as a lot of useful tips from professionals.

The desire to save money on installing a washing machine is quite natural, because buying it is already expensive. And the prices for this service, which are called by sellers in stores - about 1000 rubles - do not quite correspond to reality. As a rule, the price does not include the cost of materials, electrical work and laying of additional pipes. If all communications near the installation site are already available, then the indicated amount may be enough, but if not, it’s good if you manage to meet 5-6 thousand.

Installing a washing machine with your own hands is not so difficult. The necessary tool for this is usually available in every house or can be borrowed from neighbors. However, you need to have certain skills in working with electrical networks and plumbing. If there are none or you are not confident in your abilities, then it is better to turn to specialists: the consequences of an unqualified installation are often deplorable, not to mention the danger of electric shock. Those who know how to handle keys and a screwdriver are advised to read this article to the end: there are nuances in connecting a washing machine that are important to know about in advance.

Where to install a washing machine

The most logical place to install a washing machine is the bathroom. But the problem is that in most of our bathrooms there is an acute shortage of free space. In this case, you can install the machine under a special sink. Such washbasins are characterized by a flat bottom surface, a rectangular shape and are equipped with special drains. There are washing machines specifically designed for this installation, but the regular model will do. The main thing is that its dimensions do not exceed 70 cm in height and 45 cm in depth. It is also necessary to observe two basic rules: firstly, the sink must protrude several centimeters beyond the dimensions of the machine; secondly, it is impossible for the drain tube to pass over the machine. These rules must be observed to prevent water from entering the housing and subsequent short circuit.

When the described option is not suitable, you can refuse the bath, replacing it with a shower. The freed up space, as a rule, is quite enough if the cabin width does not exceed 80 cm.

Often washing machines are installed in the kitchen. For this, built-in models with two doors are more suitable - a transparent inner and an opaque outer. However, you can install such a machine separately, or integrate ordinary kitchen furniture that is suitable in size. The main thing is not to confuse the order of work: first install the washer, and then assemble furniture around it. At the same time, a gap of 1.5-2 cm should remain between the walls and the body. It is also advisable to provide a removable tabletop - this will make it easy to remove the machine for repair.

We carefully read the instructions

Even if you already have experience installing washing machines, you should read the technical manual before starting work. The fact is that some points may differ for different models. First of all, this concerns the height of the top point of the drain, maximum size hose extension and which water supply system - hot or cold - is connected this machine. The number and location of transport bolts also varies, and this should not be forgotten.

Preparing for installation

The washing machine can be installed on any floor, as long as it is sufficiently even and durable. Installation on a shaky wooden floor is not allowed, as this will increase the already significant vibrations that occur during washing. Therefore, if necessary, the floors need to be strengthened and leveled.

To protect the drum of the washing machine from damage during transportation, it is fixed at the factory with special bolts. When starting installation, they must be removed and the holes closed with plugs (they are supplied in the kit). In no case do not lose or throw away the bolts: you cannot transport the car without them, and then it will not be possible to return it to the store, deliver it to a service center or sell it.

The next thing to do at this stage is to screw on the inlet hose, since it will be difficult to do this later. On this preparation for installation can be considered finished.

alignment

In order for all the mechanisms of the washing machine to function without problems, it must be level. Deviation is allowed no more than 2 ° in any direction. If this value is exceeded, incorrect operation of the automation is possible and increased vibration is guaranteed, which can lead to breakdown. In addition, the body of the machine must not come into contact with walls and surrounding objects.

The machine is leveled by adjusting the legs, and the accuracy is checked using a level. This tool can be made independently from a pharmaceutical vial by filling it with water and making two transverse marks with a marker at a distance of 5 mm from the center. The accuracy of a homemade level, as well as a purchased one, is determined simply: put it on a flat surface, remember the position of the air bubble, and then turn it 180 °. If the readings are the same in both cases, the level can be used.

Adjusted feet must be locked to eliminate wobble. Putting something under them is undesirable, since these objects can move and slip out of vibration. However, if the floor still turned out to be too crooked, and the screws were not long enough, you can use plates made of durable material by attaching them to the floor with self-tapping screws or glue. In this case, the edges of the plates should protrude beyond the base of the legs by at least a centimeter.

Water connection

A flexible hose is included for this purpose. It is impossible to connect the washing machine directly to the pipes, whatever they may be. Before starting work, do not forget to turn off the tap in the desired section of the wiring.

The easiest way to connect is to install a faucet between the pipe and the faucet or toilet hose. This method is resorted to when the machine is installed in the kitchen or in a combined bathroom. If this option does not fit - you have to crash into the pipe. The complexity of this task depends on the material of the water supply. With metal-plastic, everything is simple: you can cut it with a hacksaw blade, and to put a tee, you need a pair of suitable keys. The procedure is as follows: a nut is put on the pipe, then a collet, after which the fitting fitting is inserted into it until it stops. This must be done carefully so as not to tear or move the rubber rings. We do the same manipulations at the end of the other pipe and tighten the nuts. It is not necessary to apply great efforts, trying to tighten as tight as possible: these nuts burst easily. So when they go hard and jerky - do another half-turn and that's enough.

For tapping into a steel pipe, a saddle with a threaded outlet is usually used. The place of its installation must be carefully cleaned, and then a hole with a diameter of 8-10 mm should be drilled. Aligning the hole in the pipe with the outlet of the saddle, we connect both parts with bolts. It remains to pack the thread with winding and screw on the tap or fitting. The described method is also great for plastic pipes.

Among other things, you will need to install a strainer to prevent large pieces of rust and other debris from entering the washing machine. It is best to screw it at the entrance to the apartment, but it is possible in another place, as long as water enters the car through it. And since the filter will have to be cleaned from time to time, access to it should be relatively free.

If the length of the complete hose is not enough - you should not increase it, it is better to make the eyeliner with metal-plastic. In addition, the washing machine must be powered through a separate tap, which must be closed during downtime. Neglect of this rule is fraught with an unexpected flood: no matter how reliable the intake valve is, it has every right to break.

Sewer connection

The easiest option is to insert an oblique tee into the outlet under the sink, and then connect the siphon and drain of the washing machine to it. To do this, you will also need a sealing cuff into which the hose is inserted to a depth of 5 cm, no more.

Another way is to install a special siphon with a tap under the sink. This option is more expensive, but it guarantees the absence of sewerage: the water seal will not let it through. The disadvantage of this scheme is that the siphon tends to become clogged, and then the water from the sink will flow into the washing machine. So pay attention to the check valve in its design. This is a mechanism that allows water to flow in only one direction. The valve must be cleaned periodically, otherwise it may jam.

A short hose can be extended by docking with an extension using a rubber tip and a double-sided fitting. For greater reliability, it is advisable to lubricate the connections with silicone or grab them with clamps. If the capacity of the sewerage system leaves much to be desired, and the discharge of a large volume of water is accompanied by a breakdown of the hydraulic seals, this can lead to the suction of water from the washing machine and its self-draining. For example, when you drain the water from the bath. In this case, it is better to use an anti-siphon valve instead of a fitting.

The footage of the additional hose should not exceed the size specified in the instructions. Increasing its length will increase the load on the pump, which can disable it. It is necessary either to install the machine closer to the sewer, or to bring a pipe to it. Another important point- the top point of the drain. Any section of the hose must be secured at the manufacturer's recommended height. As a rule, this is 60-100 cm. Exceeding this limit will complicate the operation of the pump, and a decrease will lead to self-draining.

If the sewer is regularly clogged, then it is better not to connect a washing machine to it. In this case, the drain is made into the toilet, bathtub or sink - whichever is closer. In this case, the hose is fixed in the desired position using the guide, which is included in the kit.

Electrical connection

The washing machine is powered from a separate electrical wiring line through a 16 A machine. A core cross section of 1.5 mm 2 is quite enough, but it is better to take 2.5. It is advisable to use copper wires: they are not as brittle as aluminum, oxidize less and withstand a greater load with the same diameter.

If the apartment is under renovation, it is better to make the wiring hidden. Ideally, you will need a grinder and a puncher for this, but you can get by with one puncher. Make a strobe about 3 cm deep in the wall and at a distance of 10-15 cm from the ceiling. Then lay the wire in it, securing it with dowel-clamps so that it does not fall out. After that, the strobe must be covered. In a renovated apartment, this option will not work. So that the wires do not spoil the interior, you can lay them under the very ceiling and close them with a plinth, and bring them to the outlet in the cable channel.

The most responsible and risky stage is the installation of the machine and the connection to the shield in the entrance. The golden rule of safety in electrical work - do not interfere if you do not know - it is better not to break it, because the price of one awkward movement can be your life. In the absence of technical training, it is better not to take risks, lay the wire to the shield, and entrust its connection to specialists. It is possible to perform such work only when there is certain knowledge and experience.

First of all, turn off the packet from which your apartment is powered. screw on free place din rail and put the machine on it. Then carefully insert the wire into the shield, strip the ends and connect, following the traditional order: the yellow core with a green stripe to ground, the blue one to zero. The third core, intended for the phase, comes in different colors, most often brown. It must be connected to the lower terminal of the machine, and to the upper one, connect the phase from the bag using a jumper. To prevent the wire from dangling, carefully grab it with a tie to the nearest bundle.

Unfortunately, there is not always grounding in the shields. In this case, it makes sense to connect the machine to the RCD. In this case, polarity must be strictly observed: the phase wire is connected to the linear clamp, and the neutral wire to the neutral one. In the presence of grounding, the RCD will also not hurt, since it works best on the third wire. So in the event of a breakdown on the body, the protection will work even before someone touches the faulty machine.

Please read the terms and conditions of the warranty carefully before attempting any work yourself. It happens that the manufacturer insists on installing the machine only by an authorized service. In this case, you will have to go there and turn, otherwise the guarantee will be lost. If, however, only incorrect installation- feel free to get to work. Of course, everything must be done in strict compliance instructions, as even minor deviations will void the warranty. For example, exceeding the maximum allowable length of the drain hose, poor alignment, or connection to a machine with a higher rating.

In the event of a breakdown, the service center specialist draws up an act on the state of the machine, which also indicates all installation and connection errors. In this case, the owner has the right to express disagreement with some or even all of the points. It is necessary to state all comments in the act with reason and put a signature under them. If you are sure that you did everything right - defend your rights.

Andrey Kazantsev, rmnt.ru

0

A washing machine, especially an automatic one, is an absolutely necessary thing in the household. You just need to load the laundry and add detergent - and then the smart device will do everything on its own.

In order for the machine to work for a long time and reliably, it is necessary to provide it with all the necessary conditions. Therefore, the moment of installation is very important. Proper connection will ensure high quality washing and trouble-free operation.

You need to think about where and how to park the car even before buying. Its dimensions, power, type of construction are determined not only by the wishes of the owners, but also by the availability of opportunities in the apartment.

Prerequisites for installation

The easiest way is to install the washing unit near the points of connection to water and electricity. In this case, there will be no problems with lengthening hoses and electrical cables.

The aesthetic component and ease of use should not be ignored either. For small apartments, the question arises whether the equipment will fit in the place intended for it.

Choose a place: in the bathroom or in the kitchen

Most washing machines find their home in the bathroom. This is the most logical choice of location, since water pipes and sewers are usually located there. In addition, household appliances will be hidden from prying eyes.

If there is not enough space in the bathroom, you can consider connecting in the kitchen or even in the hallway.

What you need to pay attention to:

• The floor must withstand vibration.
• You may have to lay communications over a remote distance.
• When measuring distances, possible unevenness of the walls must be taken into account. Just in case, the nominal dimensions of the machine should be at least one centimeter smaller than the available space.

Water connection

Machine washing, like any other, requires water in the first place. The following requirements are imposed on the water supply system: the pressure in the pipes must be sufficient, and the water must be clean. If these conditions are not met, you can put a pressure boosting pump and filter the water.

A separate tap must be built into the pipeline to shut off the water supply to the machine. This greatly reduces the chance of leakage.

Power supply

The washing machine has a lot of power. Therefore, the electrical cables and sockets available in old apartments are usually not suitable for it.

Floor quality

Serious requirements are placed on the device floor. First of all, it must be firm and strictly horizontal, without obvious irregularities. In addition, the coating will have to withstand vibration from a rotating drum.

If the floor in the apartment does not meet these conditions, it must be strengthened at the installation site of the equipment.

Positive air temperature

In the conditions of the apartment, the washing machine is always warm. However, in a country private house or a technical room, a long-term shutdown of heating is possible. This is completely unacceptable! There is always water left inside the washing machine after washing. In frost, it will inevitably freeze and break the hoses or even the pump.

Installation sequence

A new machine delivered from the store must first be freed from packaging and shipping fasteners. Then it is connected to all the required communications and the height of the legs is adjusted. After that, the unit is ready for the first wash.

Removing the shipping lock

During transportation, moving parts are fixed to avoid damage. If you do not remove these fasteners (bolts, brackets, bars), then when you turn on the mechanism, it will inevitably fail. Necessary:

• unscrew the bolts;
• remove the plastic spacers;
• take out the staples.

In place of the bolts, decorative plugs are inserted that come with the machine.

Water connection

Cold water is supplied through a flexible hose, which is included in the delivery. It is not recommended to make a completely rigid connection, since vibration will be transmitted through it to the pipe system and gradually destroy them.

The hose is connected to the water supply through a specially embedded pipe or tee. Usually it is equipped with a mesh filter to purify water from coarse contaminants. On the machine side, the connection is made via a standard screw connection.

Draining

The easiest way to organize a drain is to dip the end of the drain hose into a tub or sink. But this is more of a temporary solution.

Most often, waste water is drained through a special splitter directly into the siphon under the sink. The length of the hose must be sufficient to form a loop hanging down. There is always water in its fold, which prevents sewer odors from entering the car.

Leg adjustment

The drum of the machine must rotate smoothly and without distortion. To do this, it is necessary that its upper plane is located strictly horizontally. This can be checked using the building level. If the deviation exceeds 2°, use the machine feet adjustment. All modern models have threaded settings.

Do not put pieces of wood or pieces of linoleum under the legs. They may pop out during washing.

Power supply

The best solution is to connect the machine to the shield using a separate three-wire cable, on which the circuit breaker is installed. An RCD device is used to protect against a short circuit to the case.

The socket must necessarily be grounded and mounted at a certain height from the floor level so that water does not get into it during leakage. In the kitchen, these requirements are met by a socket for an electric stove.

Video instruction on how to install a washing machine yourself

Features of installation in various conditions

When installing the machine, it is necessary to think over the conditions and mode of operation in advance. In accordance with this, you can take measures in advance that will help to avoid problems in the future.

In a private house

During the construction or repair of a private house, it is possible to create the necessary scheme for piping and electrical cables even at the design stage. If there is a dry basement in the house, washing and drying equipment is often installed there. In this case, the residents are not disturbed by noise, smells and dampness.

In the kitchen and hallway

The washing machine fits easily into the interior of the kitchen, although the washing process itself does not go well with cooking and eating.

In the corridor, it should be installed only as a last resort.

In doing so, many questions will need to be addressed:

• where to find a place so that the car does not interfere with walking and opening doors;
• how to hide laid communications (on the floor, walls);
• how to hide appliances from the eyes of guests (built-in closet, curtain).

On wood or laminate flooring

The ideal hard and hard floor for installation is concrete. On wooden floors, the vibration of the machine increases and has a destructive effect on the unit itself and surrounding objects.

There are various options for strengthening the floor:

• concrete a small foundation;
• arrange a solid podium based on steel pipes;
• at least put an anti-vibration mat.

None of these methods will compare to a full-fledged concrete screed, but to some extent the unpleasant vibration will be reduced.

Embedded machine installation

Embedded Appliances fits perfectly into any interior. Its wires and hoses are hidden behind cabinets, and the front door is fully consistent with the rest of the headset. At the same time, such equipment is more expensive than stand-alone and its choice is not so great.

Therefore, the question often arises, is it possible to build in a conventional automatic machine? It is possible, and moreover, in various ways:

• just hide under the countertop;
• install a compact model in a finished kitchen cabinet;
• make a suitable cabinet yourself, with or without a door.

It is necessary to pay attention to the hardness of the base so that the vibration is not transmitted to neighboring cabinets.

Installing a washing machine over a toilet

Considering the small size of most toilets, the idea of ​​building a washing machine in there seems strange. But some enthusiasts manage to carry out this adventure.

Of course, you should pay attention to safety measures so that the unit does not fall on your head at a crucial moment.

• Wall quality. If the walls are fragile, it is necessary to make a steel structure supported by the floor.
• Sturdy hanging shelf. It is made from a solid metal profile.
• A safety edge so that the machine does not slip off the shelf from vibration.
• Retractable shelf to prevent laundry from falling into the toilet.
• The mounting height should leave access to the toilet flush button.

It is better to place the car behind the toilet, and not directly above it. At the same time, it is logical to choose a model with a minimum depth. And remember that for repairs, heavy equipment will have to be removed from the shelf, and then put back again.

Why the car "jumps" and how to deal with it

Increased vibration is typical for newly installed machines. But sometimes the time-tested technique begins to bounce or even move around the floor. It is necessary to determine the reasons for this behavior of the machine until it is completely out of order.

The following options are possible:

• Fasteners - bolts, brackets - were not removed before installation.
• The floor is not even enough, the machine wobbles.
• On the contrary, the floor is too smooth and slippery, then you can put a rubber mat on it.

The most easily eliminated problem is that the damp laundry has curled up inside the drum into a single lump. The operation of the machine must be stopped, hands distribute the laundry inside it and continue spinning.

There are also factors that are of a technical nature. Only a specialist repairer can identify and eliminate them:

• Shock absorbers are out of order.
• The springs on which the tank is attached are worn out.
• The counterweight mounts are loose.
• The bearing has collapsed.

All these reasons are subject to immediate elimination, the operation of the machine with such defects will inevitably lead to its breakdown.

The quality of the installation of the washing machine depends not only on the connection of the equipment itself, but also on the choice of installation location. Correctly assess the situation, take advantage of it and compensate negative points quite realistic for anyone. If there are communications, the installation process itself does not take much time. At the end of it, you need to carry out a test run - washing in an empty machine without linen. If none extraneous noise not identified, the machine can be used.

After purchasing a washing machine, most buyers do not take the issue of installing such equipment too seriously. The process of installing and connecting washing machines includes several stages. You can install according to the instructions for the washing machine. But do not forget that non-compliance or violation of at least one of the stages threatens both a quick breakdown of equipment and the danger associated with electricity or flooding the entire apartment.

Consult we have: 8 (495) 320-33-35

Whether you're buying new appliances or just transporting old ones, a professional should connect the washing machine. RusMaster specialists will quickly and efficiently perform the full range of services necessary for the correct operation of your machine. By trusting a professional master, you will not only extend the life of your washing equipment, but you will also be able to avoid many of the risks associated with self-installation.

Why RusMaster is the best choice?

Why should you order installation from us?
By placing an order for the installation of a washing machine in RusMaster, you get the following benefits:

• Guaranteecorrect connection.
  The installation is carried out by a specialist with extensive experience in this field. All communications are connected in strict accordance with safety regulations.
• Irreproachablework result. The specialist will take into account all the features of communications in your apartment and install the machine exactly where it will be convenient for you.
• Priceconnection of the washing machine is quite available. This is the cost of your peace of mind and confidence in correct connection and, as a result, reliable operation of the equipment.

What should be done before connecting the washing machine?

The instruction for any washing machine puts forward the main requirement for the electrical network - there must be grounding. This applies to how self installation, and the work of the master. After all, if washing machine connected to an ungrounded mains, warranty repairs are excluded. Even if you are installing non-new equipment, this condition is mandatory.

We install and connect the washing machine for 650 rubles.

One of the reasons to take care of grounding is the high risk of injury from electric shock in its absence. Also, the electronics of the equipment can fail even from a slight influence of static. This is an absolutely unjustified risk, threatening with huge costs for the repair of equipment or even for the purchase of new equipment. The operation of a washing machine is associated with the proximity of absolutely incompatible "phenomena" - water and electricity. Therefore, it is important to protect both yourself and your equipment.

How to connect a washing machine?

Before you buy a washing machine, you should choose a place where you want to put it. The standard is considered installation in the bathroom, but more and more equipment is placed in the kitchen. Usually such a choice is made for reasons of saving free space. In old houses, bathrooms are too small, and it is much easier to find free space in the kitchen. At the same time, communication is not difficult to stretch.

The washing machine works well only when it is installed correctly. It may be surprising, but very rarely do people get the installation right. Now we will figure out how to install the model correctly.

It is not enough just to drag the model, put it in the kitchen or bathroom and plug it in. Competent installation involves the implementation of specific actions.

First of all, we need to remove the shipping bolts that are located on the back of the case. They're big. Even if you set the washing machine correctly, but do not remove the transport bolts, the device will jump around the room during the washing process. These bolts are needed so that the drum of the machine is not damaged during transportation - they strongly compress it, and it is almost stationary.

As soon as the bolts are removed, you can proceed to the exposure of the machine itself directly. First of all, you need to understand that you can not put the device on an inclined surface or a soft surface. It is better that it be a tile - an ideal surface for the model. When installed on the floor at an angle, the machine will “jump” in the direction of the slope during the spin cycle.

Next, the machine must be leveled. Top cover should be parallel to the floor, and for this it is easiest to use a simple level. The evenness of the exposure is regulated thanks to the legs, which can be rotated, reducing or increasing their length. After setting up the machine, you need to “probe” it, because. push back and forth, left and right and make sure that the device does not bend over when you push. If you feel even the slightest push, then you need to twist the leg again in the place where the machine bends.

After setting the legs, they need to be fixed. AT different models the locking mechanism may differ from each other, so read better instruction. If the legs are not fixed at the set value, then during the spin cycle they can loosen and the length you set will simply go astray. Then the machine will start jumping again.

In principle, there is nothing difficult in leveling the machine. The level in most cases is not even used by people, it is set “by eye” in the model. This is fraught with the fact that the device rattles strongly during the spin cycle, and sometimes even jumps, but no more. Remember: the better the installation is, the quieter the washing and spinning process will be due to the absence of additional vibrations.

Please rate this article: