· Differ in high reliability, simplicity of installation and operation.

· Work with electronic keys MetacomTM2002, TM2003 and Dallas D.S.1990 A.

· Memory capacity - 508 keys (to order - 2044 key).

Programmable lock opening time 0,5 …125 seconds in increments 0,5 seconds.

· Ability to use the master key to quickly enter the programming mode.

· Modifications for electromagnetic and electromechanical locks.

· Light (light-emitting diode) and sound alarm system of opening of the lock.

· The button of opening from the room.

· Built-in watchdog timer and voltage monitor.

· Supply voltage: 12B variable or direct current.

Overall dimensions (without LED) 36 x 54 x 17 mm.

operating temperature range environment: 30…+55°C

Controllers can be supplied as part of electromagnetic locks ML-450.

1. PROGRAMMING THE MASTER KEY

a) Power off the device;

b)

c) Turn on the power;

d) Wait for 4 beeps, remove the jumper;

e) Attach the key to the contact device - you will hear 3 beeps;

“ Master key” is programmed and the device has switched to the subscriber key programming mode.

2. PROGRAMMING SUBSCRIBER KEYS

a) Attach "Master Key" to the contact device - you will hear 3 beeps;

b) Alternately applying the keys to the contact device, enter them into the controller's memory. The recording of each key is accompanied by one sound signal. If the key is defective or is already in memory, the signal will not follow.

c) Exit from the programming mode of subscriber keys is carried out by pressing the button. In this case, the device counts the duration of holding the button in the pressed state with a discreteness 0,5 seconds. The calculated duration of memorization and is used in the future as .

3. PROGRAMMING THE LOCK OPENING TIME

a) Attach "Master Key" to the contact device - you will hear 3 beeps;

b) Press the exit button. In this case, the device will calculate the duration of holding the button in the pressed state with an accuracy of 0,5 seconds. The calculated duration is remembered and used later as lock opening time.

4. CLEAR KEY MEMORY

a) Power off the device;

b) Close the jumper on the PCB;

c) Turn on the power;

d) Wait for 4 beeps; Then there will be a ten-second pause and the sound signal will turn on again;

e) Within 3 seconds after the start sound signal remove the jumper;

f) After waiting for the sound signal to stop, reinstall the jumper;

g) After a pause (memory is being cleared at this time), the program will restart. In this case, since the jumper remains installed, the device will enter the programming mode "Master Key", and you will hear 4 beeps (see point 1) . You can program "Mother Key" or turn off and then turn on the power of the device if "Master Key" remains the same.

Note:

· "Master Key" when clearing the memory is saved;

· If after clearing the memory (p. 4, g) you hear a long (3 seconds) beep, this indicates a malfunction of the memory chip. Repeat cleaning. If the result is negative, replace the 24C16 chip;

If the jumper is not removed within 3 seconds after the start of the sound signal (item 4, e), the device will go into test mode - cyclic on / off electromagnetic lock with a period of 6 seconds (3 seconds the lock is on, 3 seconds - off);

If the jumper is not reinstalled after the end of the beep (item 4, f), the device will switch to normal mode work without clearing the memory.

More full information information about METAKOM products can be obtained from the sales department

at the address st. Usacheva d.29, bldg. 8, under. 42 (code-444) and phones (0,

www. ***** E-mail: *****@***ru

Manual for electromagnetic lock controllers ELC series

The controllers of the ELC series are designed to be built into the Metacom ML-450, Accord ML-194 or similar electromagnetic locks.
- Can be used in conjunction with access control devices that do not have an electronic key reader.
- Differ in high reliability, simplicity of installation and operation.
- Work with Metakom TM2002, TM2003 and Dallas DS1990A dongles.
- Memory capacity - 508 keys (on request - 2044 keys).
- Programmable lock opening time 0.5…125 seconds in increments of 0.5 seconds.
- Ability to use the master key to quickly enter the programming mode.
- Modifications for electromagnetic and electromechanical locks.
- Light (light-emitting diode) and sound alarm system of opening of the lock.
- Opening button from the room.
- Built-in watchdog timer and voltage monitor.
- Supply voltage: 12 V AC or DC.
- Dimensions (without LED) 36 x 54 x 17 mm.
- Operating ambient temperature range: 30…+55°C
ELC series controllers can be supplied as part of ML-450 electromagnetic locks.

BRIEF INSTRUCTIONS FOR USE
ELC SERIES CONTROLLERS

1. PROGRAMMING THE MASTER KEY


c) Turn on the power;
d) Wait for 4 beeps, remove the jumper;
e) Apply the key to the contact device - you will hear 3 beeps;
The “master key” is programmed and the device has switched to the subscriber key programming mode.
2. PROGRAMMING THE SUBSCRIBER KEYS
a) Attach the “Master Key” to the contact device - you will hear 3 beeps;
b) Alternately applying the keys to the contact device, enter them into the memory of the ELC series controller. The recording of each key is accompanied by one sound signal. If the key is faulty or already in memory, the signal will not follow.
c) Exit from the programming mode of subscriber keys is carried out by pressing the button. In this case, the device counts the duration of holding the button in the pressed state with a resolution of 0.5 seconds. The calculated memorization duration is used later as the lock opening duration.
3. PROGRAMMING THE LOCK OPENING TIME
a) Attach the "Master Key" to the contact device - you will hear 3 beeps;
b) Press the exit button. In this case, the device will calculate the duration of holding the button pressed with an accuracy of 0.5 seconds. The calculated duration is stored and used later as the duration of the lock opening.
4. CLEAR KEY MEMORY
a) Power off the device;
b) Close the jumper on the PCB;
c) Turn on the power;
d) Wait for 4 beeps; Then there will be a ten-second pause and the sound signal will turn on again;
e) Within 3 seconds after the start of the sound signal, remove the jumper;
f) After waiting for the sound signal to stop, reinstall the jumper;
g) After a pause (during this time the memory is cleared) the program will be restarted. At the same time, since the jumper remains installed, the device will enter the “Master Key” programming mode, and you will hear 4 beeps (see point 1) . You can program the "Master Key" or cycle the power of the ELC series controller if the "Master Key" remains the same.
Note:
“Master key” is saved when clearing the memory;
If after clearing the memory (p. 4, g) you hear a long (3 seconds) beep, this indicates a malfunction of the memory chip. Repeat cleaning. If the result is negative, replace the 24C16 chip;
If the jumper is not removed within 3 seconds after the beginning of the sound signal (item 4, f), the ELC series controller will switch to test mode - cyclic switching on / off of the electromagnetic lock with a period of 6 seconds (3 seconds the lock is on, 3 seconds - switched off);
If the jumper is not reinstalled after the sound signal stops (item 4, f), the device will switch to the normal operation mode without clearing the memory.

information about delivery

Terms and delivery time

Delivery of the order in Moscow is carried out on 2 business day

Delivery of the order in St. Petersburg is carried out on 3 business day, after processing the order by the manager of the online store (order confirmation by phone).

- Delivery in Moscow within the Moscow Ring Road and in St. Petersburg carried out Monday through Saturday, excluding public holidays, 09:00 to 21:00 .

- Delivery outside the Moscow Ring Road carried out Monday through Saturday except holidays,

— Delivery to suburb of St. Petersburg carried out Monday through Saturday except holidays, from 09.00 to 19.00 (without determining the minimum interval).

Shipping cost for ordered items

– Delivery in Moscow (within the Moscow Ring Road) subject to cost orders over 2000 rubles carried out is free.

— The cost of delivery in Moscow (within the Moscow Ring Road) of the order for less than 2000 rubles is 200 rubles.

– The cost of delivery in Moscow to areas outside the Moscow Ring Road (Zhulebino, Yu. Butovo, Mitino, etc.), as well as in the Moscow Region within 10 km from the Moscow Ring Road, is 250 rubles regardless of the amount of the order.

– The cost of delivery in the Moscow region from 10 km to 30 km outside the Moscow Ring Road is 450 rubles regardless of the amount of the order.

— The cost of delivery in St. Petersburg depends on the weight of the order. The minimum shipping cost is 300 rubles

— The cost of delivery in the suburbs of St. Petersburg depends on the weight of the order. The minimum shipping cost is 450 rubles. The approximate cost of delivery is calculated automatically when placing an order and is specified by the manager of the online store when confirming the order.

- To the cost of delivery of orders, including those delivered free of charge, by weight over 10 kg added 20 rubles for each subsequent kilogram. Check the final shipping cost with the manager of the online store.

— Please pay attention to buyers from Moscow, Moscow region, St. Petersburg and Leningrad region, what order weighing 30 kg or more is delivered only to the entrance (without lifting to the floor).

Stock of goods in the store

• order with the condition of goods reservation in a retail store - 1 calendar day from the moment you receive an email notification that the order is ready for pickup