This morning I drank tea and flipped through the news on the Internet, spilled tea on the keyboard, quickly pulled out the batteries, turned it over and shook it over the sink, wiped it with a towel (leaving it upside down as well), came home from work in the evening, started chatting and realized that the buttons didn’t work. so smoothly, slowly return to their place when pressed, get stuck, crunchy, sticky, etc.

I twisted the keyboard in my hands, realized that the case was all-metal, and the back plastic part was tightly glued, googled the forums and was convinced of my assumption.

I had to do everything "outside" digital block works fine, only letters are buggy, so I did like this

The buttons on the scissor mechanism are pried off with a fingernail (well, or with a screwdriver), to remove the button, you need to gently hook it from above and pull it until it clicks, if there is no click, then pull the left and right upper corners, after the upper part of the button is unhooked - gently unhook similarly, be extremely careful, you can break the mechanism.

We arrange the buttons on the table in rows so as not to confuse their location; during the reverse operation, we will put them in place from left to right in rows.

For washing, we need a tube of clean water or isopropyl alcohol, for example, monitor wipes are fine.

It is necessary to evenly spray the liquid over the open push-button mechanisms (move quickly with your hand when puffing), after spraying, wait 20-30 seconds, carefully move each scissor mechanism and gently wipe each hole (sticky tea usually sticks around), wipe the entire keyboard, briefly blow it with a hairdryer and make sure that the keyboard does not heat up, otherwise you can damage the plastic mechanisms.

Now we wipe each button around the perimeter and from the inside and install it back, you just need to put the button in a niche and gently press it and push it in all corners.

Particularly noteworthy are the elongated buttons such as tabs, caps, spaces, etc., they first need to put the lever through the holes, and then put the button and snap it into place.

I do not advise once again to remove the buttons, because. soon they will wear out from such use and will fall out on their own, so remove only problematic buttons.

This method can also help if dust or wool has clogged into the scissor mechanisms, if the buttons become clogged, they begin to creak, stick, lose their smoothness, etc.

By the way, on the last keyboard that I took to work - I slightly lubricated the perimeter of the spacebar and the lever at the place of its contact with the metal, this saved me from the squeak.

It is worth noting that the keyboard turned out to be very resistant to moisture, usually when flooded, the keyboard stops responding to pressing, and the contact tracks turn into mush.

However, I would advise Apple make slightly better devices and stable operating systems, often inferior in reliability and ergonomics appearance devices (such as a mouse).

Although in fairness it is worth noting that all these apple gadgets in the USA cost almost the same as similar products from competitors, and duck accessories are generally very high, in some stores branded headphones can cost about 3000-4000 rubles, and in the USA about 4 times cheaper, I also found keyboards on the same Avito at a price higher than the new one in "special places", I just have friends who bring devices from various suppliers without extra extra charges))) When I bought a router AirPort Express for 3400, then in some "branded" stores in the city the price reached 5900.

Apple is the undisputed leader in the electronics market. All Apple devices have excellent specifications. But, in any case, not even a super reliable gadget is immune from breakdowns. You can, for example, accidentally hit your computer or spill liquid inadvertently. AT Apple computers most often the keyboard fails. Then the user begins to wonder how best to repair the apple keyboard. Most often, the keyboard stops working due to mechanical damage as a result of impact, falling or due to moisture. It happens that apple keyboard repair is necessary due to too diligent and long-term use of the part. In order to make a quality one, you should contact a qualified specialist who has the skills to work with defects of any complexity, since the apple keyboard has its own characteristics. The keyboard of apple laptops is the part that is most often damaged due to physical impact. When a breakdown occurs, you can hardly use the computer. Quite often this becomes impossible at all. Such defects bring a large number of inconveniences to users who need a computer to work here and now. Then, in force majeure circumstances, MacBook owners begin to organize apple keyboard repairs. The cost of repairs and the length of time depends on the severity of the problem. In any case, before starting any intervention, it is necessary to diagnose the broken node using special equipment and tools. In order to bring the keyboard back to life, you must first figure out what exactly the problem is.

apple keyboard defects

The most common apple keyboard defects that require an apple keyboard repair consist of the following faults:

• keys do not work, stick;
• problem in the supply chain;
• the case is deformed or broken;
• broken keyboard mount
• the computer "does not see" the keyboard;
• failure of the loop or controller.

First you need to understand that there are two types of keyboard: wireless and with USB interface. First of all, check if the keyboard is properly connected to the main computer and if all the settings and instructions have been completed properly, and whether there is a charge on the batteries, suspected to be a malfunction of the keyboard, or not. If the problem is not banal, then you definitely need to carry out apple keyboard repair.

Before describing breakdowns step by step and telling how to repair an apple keyboard, it should be clarified that, unfortunately, apple aluminum keyboards cannot be disassembled. Rear end the case in such a keyboard is tightly soldered, and it is not possible to open it yourself without damaging it. Even in some cases, it will still offer to replace a keyboard that cannot be repaired.

When dust and small hard objects get under the buttons on the keyboard, for example: crumbs, grains of sand - almost always in such cases good exit From the current problematic situation, it is to carry out a proper repair of the apple keyboard keyboard, namely, to clean the computer keyboard. True, in case of serious damage, such an apple keyboard repair will not save the situation, and this part of the device will need to be replaced. Since you can’t get out of the situation without disassembling the case, it’s better not to charge apple keyboard repair lovers.

Keys don't work, sticky.

Moisture may have entered the device. In this case, it is necessary to remove the batteries as soon as possible and dry the place of the bay. Otherwise, the contact tracks and internal elements will oxidize. Inside the keyboard there are moisture indicators, they will show the degree of moisture penetration. Undoubtedly, apple keyboard repair, namely, cleaning after moisture ingress must be entrusted to a responsible specialist. Most likely, he will carefully remove the keys with the help of a special tool, and also clean the backing and fastening of the buttons. He will do it quickly and qualitatively, while regular user it will only take half a day to unscrew the bolts (and there are a great many of them). It happens that the internal components of the keyboard have already been heavily oxidized, then the repair of the apple keyboard keyboard is carried out only by replacing old keyboard to a new one.

The problem is in the power supply.

To fix this problem, first you need diagnostics, and then you can start repairing the apple keyboard. In this case, you need to intervene in the key elements of the keyboard. Here, the owner of the computer can not figure it out on his own. The master, using a microscope, will look at the condition of the contact tracks and if there are any damages. If the supply chain is interrupted, it must be renewed. This work is carried out with special tools.

It may be necessary to change the substrate and with it the keyboard contact pad or to change the backlight. Here, the repair of the apple keyboard keyboard will take place as follows: the master only changes the base along with the electronic components of the Apple keyboard. After that, all mechanical components must be properly cleaned and installed on a new base. Although, it should be noted that this apple keyboard repair occurs only occasionally. Very often, due to liquid getting on the keyboard, the backlight of the keyboard fails, as a result of which it is necessary to replace such a backlight. And only a responsible specialist with the help of necessary tool. And here you need a master with the necessary qualifications to make an apple keyboard repair.

The case is deformed or broken.

In this case apple keyboard repair performed only by replacing the damaged device with a new one. Entrust this procedure to an experienced specialist.

Breakage in the keyboard mount.

If the keyboard mount breaks, you need to change the keybod buttons. This apple keyboard repair at a professional level, only a master can do it. In some models of MacBooks, it is not possible to replace individual elements of the keyboard. In this case, it is necessary to change the complete set: the substrate together with mechanical units (buttons and fasteners).

The computer "does not see" the keyboard.

This breakdown is typical for wireless keyboard. To fix this problem, you need to Bluetooth setting. First you need to make sure bluetooth is turned on. Recheck all settings. In addition, see if the batteries in the device are charged. If after rebooting the problem is not solved, you need to contact a specialist and organize apple keyboard repair.

Breakdown of the loop or controller.

The main reason why the keyboard does not work properly or does not work at all is a broken keyboard cable or keyboard controller. To find out the essence, it is necessary to carry out technical diagnostics and then do apple keyboard repair or to replace nodes that are out of order. This work at the proper level can only be carried out by an experienced specialist.

Sometimes the reason for the failure of the keyboard is a malfunction in the computer motherboard. With such a problem, you may have to do complex repairs to the elements. motherboard which, of course, cannot be done at home.

The most expensive apple keyboard repair is to replace the top case (this is the bottom cover of the computer, along with the keyboard and touchpad of the MacBook Pro or MacBook Air). The cost of this node is quite high. Such an apple keyboard repair will have to be carried out if the internal elements of the device are badly damaged due to moisture.

Difficulties during keyboard repair

It may seem that disassembling a computer and replacing an apple keyboard is not a difficult process. But if the repair of your computer is that you only need to change the keyboard without touching the top case, it is very difficult to carefully separate the old keyboard, it is very easy to get confused in a large number of fasteners. In addition, sometimes the fasteners themselves need to be replaced with new ones. The next difficulty is that when dismantling the keyboard, you must use the right tool, otherwise there is a risk of damaging the case and then you have to change it completely. And one more nuance, if you are replacing only one keyboard, then you need to take into account the fact that removing the substrate without damaging the contact tracks is quite difficult, so you need to trust apple keyboard repair only to qualified craftsmen.

In order for the apple keyboard to serve you and your computer faithfully, you must, of course, treat your device with care. But, nevertheless, not a single thing from breakdowns electronic device is not insured, so sooner or later you will face the need to repair the apple keyboard, and then seek help only from specialists. Do not save on the work of a professional, as he will take the task with all responsibility: he will diagnose and repair the keyboard properly using special equipment and tools. As a result, the computer will please you with its uninterrupted operation for a long time.

It all started with the fact that one day I was flooded with red wine on a wired keyboard from Apple (MB110RS). The maximum that had been done before, when I found out about it, was only the removal of external traces of liquid ingress.

It should be noted that this keyboard is not in vain considered one of the most convenient of its kind in principle: easy quiet key travel, completely free and relaxed hands when working on it, nice design.
So, it was precisely its main advantage - the easy movement of the keys - after wine got under them, the keyboard almost lost: the buttons, especially the bottom row, began to stick - Shift, Ctrl, Alt, Cmd and, first of all, Space. This is understandable - due to the tilt of the keyboard, the liquid that got into it rushed to its lower part, and the wine, the water from which had time to evaporate, left its dry residue on the contact pads, springy rubber bands and under the keys. In fairness, it should be said that even after that the keyboard continued to work.

It was decided to restore. But! After 10 minutes of searching, it turned out that the keyboard is absolutely non-separable - not a single screw! Like a layer cake, it consists of glued to the bottom by means of films and foil printed circuit board and aluminum frame.

However, you can stick it even with a hairdryer:

But in the end, it will be an unattractive spectacle.

Autopsy apple keyboard aluminum

Believe the sad experience of all those who have tried this path for themselves, the end result is not worth it. And then there are no guarantees that it will be possible to assemble everything back in its original form.

Of course, for a simple cleaning of the dirt under the keys, it is enough to remove them and remove the dirt. But it seemed to me too tedious to remove each of the 110 keys in turn.
In short, I decided to choose the clumsy and neat path at the same time - just bathe in water and then dry well.

So, how I restored the Apple keyboard after a liquid hit:

PS: I do not pretend to be the only correct method of washing / cleaning / drying the keyboard - I did everything intuitively. Satisfied with the result.

I believe that when clave is poured with tea, coffee, milk, juice, cocktail, mineral water, beer (underline as necessary), the recovery algorithm will be the same. The only exception is carbonated drinks: they must be washed off immediately with any clean water, until the acids contained in them begin to corrode the contact pads, otherwise you will probably have to say goodbye to your push-button friend.

There are tips for the very lazy - put the keyboard in the dishwasher. I would not unequivocally recommend this method - the introduction of various detergents is unlikely to have a positive effect on electronic components and pads on the printed circuit board. But the taste and color...

Photos of the disassembled devices are taken from here.

Under the keys in your computer, there is probably dust, crumbs, pieces of food, hair and other debris. Even the most tidy Mac users can't keep their keyboards clean.

The buttons on Apple computers are well-fitted, the openings in the case have a minimum gap, but even this is enough to regularly collect a batch of garbage.

Why Clean Your Keyboard

Firstly, it is useful from a hygienic point of view. Computer keys are the first hotbed of germs and bacteria in the house after the toilet. It’s not every time I wash my hands before typing something, and if it’s a laptop, it will still collect dirt from the office, cafe and travel bag.

Secondly, dirt and dust can cause the buttons to stick. Contacts on the board may become clogged and respond to pressing not the first time.

Thirdly, clean keyboard looks aesthetically pleasing. The Mac looks like new.

How often to clean your keyboard

It all depends on your desire and how you use your Mac. Home computers are recommended to be cleaned at least once every three months. Portable laptops should be cleaned every 30 days.

How to clean your keyboard

Cleaning the keyboard is divided into two stages: external and internal. External cleaning of the keys can be carried out as they become dirty or at the request of the user. It is aimed only at removing dirt from the surface of the keys and will not affect the operation of the device.

Internal cleaning is aimed at removing dirt and debris under the buttons. This procedure must be carried out regularly to avoid contamination and sticking of the buttons.

External cleaning

For external cleaning, it is not necessary to turn off the computer or turn off external keyboard. You can use the KeyboardCleanTool for Mac utility. This free utility locks keys and prevents false presses during cleaning.

Don't forget to grant permission to the app along the way Settings - Security & Privacy - Accessibility(administrator password required).

After blocking, we arm ourselves with microfiber, cotton swabs or discs. They must be slightly moistened with water or an alcohol-containing substance. You can use special wet wipes to clean the keyboard and display.

Attention! The liquid should not drain from a rag, cotton wool or napkin. If you're worried about wetting, it's best to play it safe and turn off the computer's power.

Thoroughly wipe all buttons from the front and along the ends. Don't forget to wipe the surface of the keyboard itself, lower part and feet (for external devices).

How to clean your keyboard from the inside

This is a painstaking and laborious process. Be patient and have at your disposal up to an hour of time. To get started, take a picture of the location of the buttons on your smartphone, so that you don’t painfully remember the layout later.

Be sure to clean the inside while the computer is powered off.

Use a toothpick or plastic tool to pry upper corner keys and carefully pry the mount out of the groove (do not use screwdrivers or knives as they may damage the keys).

Now grab the entire button and unfasten the mount from the second slot.

Attention! Excessive use of brute force can break the keys. Be careful.

If the fastening mechanism remains on the keyboard, unfasten it and secure it to the key.

When all the buttons are removed, you can clean the debris with a vacuum cleaner. Remaining dirt and particles should be removed with a lint-free, slightly damp cloth.

Wipe the buttons themselves with wet wipes or an eraser.

We put clean buttons in place. We put the key with the fastened mount in place and press it around the entire perimeter until it clicks. We press several times and make sure that all the fasteners are in the right grooves.

Here's a cheat sheet if you forgot to take a picture of your keyboard:

Wait for the keyboard to dry completely before turning on the computer.

Do not forget to regularly monitor the condition of the keys and clean them. Do it right now - and tomorrow you will say Thanks yourself for it.