The following prompted the purchase of this remote control. My youngest son dropped the Iconbit MovieHD C Plus remote control

This turned out to be enough for the remote to fail. During disassembly, it turned out that the processor sprayed on the board did not work.
Unfortunately, many of the commands for controlling this Iconbit device were only from the remote control.
Having bypassed the remote control sales points and made calls to service centers, I decided to buy such a remote control
in Belarus it’s unrealistic. And deciding that abroad will help us, it’s useful to search on Aliexpress.
As a result, this remote control was bought. Further, after removing a few commands from my native console, I found
analogue, where there were almost all the control buttons. By writing a letter to the developers of this remote

I asked them to distribute the commands to the keys I need and enter them into the database.
Thank them for this.

The remote itself

MiniUSB connector for connecting to a computer, covered with a rubber plug


The remote control is powered by 3 AAA batteries, I have not changed it for a year of use. The remote control is very economical.
Assembled on a PIC controller.


Using the remote.
After downloading and installing the RCCreator program and connecting the remote control to the computer, we get
a database of different remotes and the ability to download codes for four devices.
The database is extensive and replenished from the Internet, you can add your own.


You can download codes from other remotes by saving them in the database.

Instructions for use

Additional Information

Information for everyone
Just because your remote doesn't exist doesn't mean you're out of luck. Mine didn't exist at first either.
We are looking for a similar device, by button codes (if we managed to remove it), by brand, by purpose.
Next, we write out the codes from the triggered buttons, compile a code correspondence table
to the necessary buttons, we send it to the developer of the consoles (see the preface). He makes a remote control for you and enters the device into the database.
How I removed the codes from my remote.
The remote didn't work. Having disassembled, I warmed up the controller with a hairdryer.
Earned 10 buttons out of 20, though not for long. I quickly copied them. Having native codes, it is easiest to find a similar device.

We thank you for purchasing the CHANGER Universal Programmable Remote and hope you enjoy our remotes.

To program the remotes, you will need a miniUSB cable, which can be purchased at any computer store, or you may already have one (currently this connector is quite widely used in phones and other devices of various brands). Before using the remote control, we strongly recommend that you follow all the instructions in the instructions step by step.

Remote programming instructions

Download latest version program installer. Run the installer. Select the installation folder and other options. For the correct operation of the program, it is recommended to agree with all the options of the program installer.
The programming of the remote control must be carried out with established elements nutrition.

The first thing to do is find the right remote control and determine what type of ChangerUSB it is filmed in. And connect this type of Changer for firmware.

This is the most important thing to understand in programming. I'll tell you how to do it. We chose the firmware by highlighting it with the cursor. Go to the next window located in the middle of the program and determine the type of remote control (Changer) for the firmware. To do this, iterate over the devices, from top to bottom.

If you have selected the device correctly, the inscriptions should appear like the following figure. Button names or button IDs.

After this has been found out, it is necessary to connect exactly such a Changer as in the program figure, where the button IDs and names appeared.

In the lower part of the RCCreator program window there are two connection status indicators: on the left - the remote control, on the right - the signal receiver. Before you start working with the program, make sure that the icon of the device you are connecting turns green.

If the type of firmware and the connected bullet are selected correctly, the button to program the remote control becomes active. click (Program remote)

Press (+) to start programming:

The red diode on the remote control lights up, which means the programming process has begun. After the diode has gone out, the programming process is ended accordingly. In the programming tab, the data of the recorded remote control will be indicated. After finishing the programming process, close the programming window and only then disconnect the remote control from the miniUSB cable.

It remains to print the instructions by clicking on the Printer icon in the program. Everything. The remote control is ready to control the device for what it was asked for.

Service capabilities of the program

AUTO SEARCH - under development

SEARCH BY BUTTONS - this is a search for interchangeable remotes that have the same signal both from the same manufacturer and in others, in the same or different types of remote control housing. Open the search tab, remove the “POWER” button signal from the remote control, the button signal will be displayed in digital form at the top left of the tab. press the “POWER” button in the “SEARCH” tab, a list of remote controls matching the signals of the “POWER” button will be displayed on the left. it is recommended to use the signals of the following buttons for searching - “POWER, 1, VOL +, CH +, OK, MENU”.

SEARCH BY PROTOCOL - this is a search by the signals of the remote control buttons that are not in the "SEARCH" tab. there are 2 buttons […] for this, the search process is similar to searching by buttons.

SEARCH BY BUTTONS AND PROTOCOL OF THE REMOTE AVAILABLE IN THE BASE - is used when the remote control is already in the database of the program, and you need to select either an analogue or compare with another remote control available in the database. select the desired remote control in the program, select the desired button with the mouse so that it becomes active on the CHANGER remote control on the right and its numerical value is displayed in the signal indicator field. Open the SEARCH tab and paste it into the desired button. A list of analogues will be displayed on the left in the program.

Before you start removing codes from remotes for the first time, we recommend that you read the instructions, which can be found through the menu "About the program" - "Help".

We also recommend that you read the information below:
After the codes of all buttons are recorded, it is better to close the program through the "exit" or "cross" in the upper right corner - the information is saved when closing. The program may close with an error, which will result in the loss of the last entered data.

For greater confidence in the safety of the remotes you removed, we recommend exporting the codes to a separate folder. To do this, create, for example, a folder named "DRC" in any convenient location. After removing the remote control codes, select "File" - "Export" and select the folder you created. For additional protection data just in case, we highly recommend doing it regularly backup removed remotes to other media. We would be very grateful if you could send the removed remotes to our email address. Particularly active will receive additional discounts on remotes.

In the house of each of us there are many different electronic devices, and almost everyone at least once faced the problem of finding a remote control. remote control to one device or another. The process of searching for a remote control does not always go quickly and painlessly, meaning the mismatch of codes when selecting a remote control from the catalog, improper performance of functions, and much more.

Programmable remote controls are a new generation of remote controls that will help you solve almost any problem of controlling appliances in your home. CHANGER USB will save you from a long search for a TV remote control, DVD player, audio center, tuner satellite television etc., moreover, you can CHANGER USB 4:1 combine control function with four various devices in one remote. For regular user convenience lies in the fact that it is possible to flash a blank in mode from the Internet via USB port your computer by selecting the firmware from the database in the program. Those who deal with remote control professionally are given the opportunity to create their own database of firmware, remote controls and, accordingly, make a copy of the remote control at any time at the request of the client.

The RC Marker program, which reads the original remote control and writes to the CHANGER USB, is easy to use and does not require special knowledge and you can make a clone of any remote control within 5 minutes.

We thank you for purchasing the CHANGER Universal Programmable Remote and hope you enjoy our remotes.

To program the remotes, you will need a miniUSB cable, which can be purchased at any computer store, or you may already have one (currently this connector is quite widely used in phones and other devices of various brands).
Before using the remote control, we strongly recommend that you follow all the instructions in the instructions.

REMOTE PROGRAMMING INSTRUCTIONS

Before reading the manual, please note that this manual is written for the RCMaker program and for the Changer USB1. On the this moment Changer USB1 remotes are no longer sold and the programming software is RCCreator, which is an improved version of RCMaker. Instructions for using the RCCreator program are located.

Insert the program disc, then launch RCMaker USB. This will launch the program installer. Select the installation folder and other options. For the correct operation of the program, it is recommended to agree with all the options of the program installer.

If you are going to program the USB Changer 1in1 remote control (for one device), then make sure that the batteries are removed from the remote control. Changer 1in1 Remotes with Batteries Inserted not programmed. The Changer 4in1 remotes are programmable whether batteries are inserted or not.

In the lower part of the RCMaker USB program window there are two connection status indicators: on the left - the remote control, on the right - the transmitter. Before you start working with the program, make sure that the icon of the device you are connecting turns green.

Select in the program the remote control that you would like to make in the Changer USB case. Pay attention to the fact that the body of the remote control shown in the right part of the program window coincides with the body of the Changer USB remote control. Select the USB Programm icon on the panel, which becomes active after connecting the remote control, then press (+) to open the programming window.

If the red diode on the remote control lights up, then the programming process has begun. After the diode has gone out, the programming process is ended accordingly. After the end of the programming process, close the programming window and only then disconnect the remote control from the miniUSB cable.

Programming is also possible from our website

RECOMMENDATIONS FOR REMOVING CODES

Before you start removing codes from remotes for the first time, we recommend that you familiarize yourself with the instructions, which can be found through the menu "About the program" - "Help". We also recommend that you read the information below:
After the codes of all buttons are recorded, it is better to close the program through the "exit" or "cross" in the upper right corner - the information is saved when closing. The program may close with an error, which will result in the loss of the last entered data.

For greater confidence in the safety of the remotes you removed, we recommend exporting the codes to a separate folder. To do this, create, for example, a folder named "DRC" in any convenient location. After removing the remote control codes, select "File" - "Export" and select the folder you created. For additional data protection, just in case, we highly recommend regularly backing up removed remote controls to other media. We would be very grateful if you would send the removed remotes to our email address [email protected]. Particularly active will receive additional discounts on the guns.


TECHNICAL SUPPORT

When you first contact the service technical support Tech.corp.TK&KT, you need to answer the following questions:

• What is your name and what city do you live in?
• Where did you buy the CHANGER
• What kind of help do you need - could not program the remote?; programmed, but it does not work on the device; can't find a suitable remote control in the program database? other;

The more detailed you answer, the faster we can help you.

I would like to draw your attention to the fact that many new types of equipment and new brands have appeared lately, we simply do not physically have time to keep track of all the new products and post them on the site.

If you did not find the remote control you are interested in in our database, then send a request to the same email address: [email protected] Perhaps we can help you.

To facilitate the search for data on the remote control you need, you must indicate the exact model of the device and the manufacturer (brand), attach a photo of the original remote control, its number, give a link to the instructions for the device. Without these data, a request to search for a remote control will not be considered!

You can download the most up-to-date version of the RCCreator program at . To work in this version of the program, you need a USB 4:1 remote control, because. it has a built-in IR receiver.

CHANGER - USB programmable remote control. Depending on the remote control model, it allows you to control 4 devices, contains 48 buttons, the number of which
is increased by 2 times using the SHIFT service button. This remote control can be programmed both online on the manufacturer's website, and on your own computer with
using the RCCreator program, the database of which contains more than 4000 firmware from BQS and GBS consoles of the 80s of release, to latest LCD TV, LED TV, DVD
players, satellite tuners, home theaters and car radios with TV and DVD support. Universal remotes allow you to control several devices related to
various types (TV, DVD, digital receiver, audio system). The remote control is powered by three AAA batteries.

Preparation for use.
To work with the remote control, you will need a computer, the RCCreator program (you can download it from the manufacturer's website) and a USB - mini USB cable.
modifications of the Changer console.

The filter allows:
1. Set brand. The database supplied with the RCCreator program contains data on remote control models for video and audio equipment manufactured by various manufacturers.
2. Select device type. Devices, which have information in the database, are divided into 19 categories (TV, SAT, DVR, HiFi, AUX, VCR and others). To use the filter, you can specify several device types from this list.
3. Specify the device model. The data of the remote control selected by the search filter can be saved as a file in XML format. Previously created console database files can be imported into the currently used database.

At offline use As a versatile device, the Changer RC USB 4v1 can be programmed to control up to four different products.
Programming is carried out using the RCCreator program. For programming, data stored in the manufacturer's database or created by the user can be used.
When programming, the remote control selected from the base can be assigned to one of the types of devices (TV, DVD, SAT, AUX). To program all four devices, it is required to sequentially
select them from the database, and then write them to the memory of the Changer RC. The programming procedure takes a few seconds. You can follow the progress of programming
Power indicator. To delete the recorded remote control, the “Clear.

Usually Universal remote remote control (RC) is a small box with LEDs, circuits and buttons. It works due to the fact that the infrared sensor on it transmits desired code to the same sensor in another device. With it, for example, you can adjust the sound volume, switch channels, change the power of a device, and much more. It differs from the usual universal remote control in that several electrical appliances can be recorded simultaneously in its circuit. Today we will look at how to set up a universal TV remote control.

Setting up a universal TV remote

It will be pretty easy to do everything. It may not work the first time, but don't despair.

If you haven't bought it yet, you can buy it in China at a very low price.

The setting includes several ways:

1. Press and hold SET (TV) until the red LED is active, then once on POWER, then enter the TV code and the indicator should turn off. If the indicator does not go out, then you must press the MULT button after entering the code.
2. Dial the desired number and simultaneously hold SET (TV) and POWER.
3. Hold SET (TV) until the red LED is active, then press POWER once, point the remote control towards the switched on TV and wait for its reaction. Then to the MULT button.

In the event that the device does not start to work, you need to try entering a different number for the existing TV model, or use the 3rd method.

If you don’t want to set up the remote control yourself or it doesn’t work, then you can ask an employee of some electronics store, you just need to know the TV code.

Setting up a universal remote without a code

AT this method you will have to do the setting yourself and without entering the number. To do this, you first need to turn on the TV. Then on the remote you need to hold down a button called Set for a few seconds, or it may still be SETUP (TV) until the red sensor becomes bright. Point your all-in-one towards the TV and press the green POWER button. The indicator should start blinking, which means the device has begun to select a code for your TV receiver. We are waiting for some kind of reaction to occur on the TV. For example, the sound will turn off, the channel will switch, etc., this reaction depends on the brand of the TV or even on the remote control. After waiting for the reaction, you must immediately press the MUTE button.

Pdf instructions for setting up the Rolsen remote control

Below is the official Rolsen tuning manual: RRC - 200, RRC - 300. It may be suitable for other devices.

After waiting a few seconds, the indicator will turn off and you can use it. If it didn’t work out, then try to turn off the sound after turning on the TV and after selecting the channel, and then do the same steps that are described just above. If you did everything correctly and your devices are really working, then the setup should be successful.