Before you set up Tricolor TV on your TV, you must carefully read the instructions for installation and internal settings. Only a well-performed installation will avoid the appearance of any difficulties during use. Installing the system is quite laborious, but allows you to save on the services of a master. If you first study step by step instructions, then there will be no problems during installation and synchronization of equipment. You should also study the settings in advance so that the receiver works correctly.
First you need to independently fix the antenna on the outer wall of the house and adjust the mirrors to the satellite. To do this, you need to pay attention to the following points:
- Choice of installation location. The dish should be fixed in such a way that it is located on the side of the satellite, which is located on the equator and is located in the south. Please note that there should be no obstacles between the satellite and the antenna. Even small trees can create significant interference.
- Distance between equipment. The closer the tuner and antenna are, the clearer the system will work. In this case, setting up the receiver will be much easier.
- Correct installation. When assembling the antenna, keep in mind that the converter must be installed with the holder up. This eliminates the possibility of a negative impact of precipitation on the functioning of the system, protecting the "heads" from bad weather.
- Reliable connection. The converter should be connected to the cable using a special F-connector. This eliminates the possibility of malfunctions during operation. The cable must be insulated no more than 10 mm. The connector must be twisted as much as possible.
Antenna adjustment process
The more precisely the dish is adjusted from the side of the geographical position, the better the signal can be achieved at the output. The peculiarity of this procedure lies in two criteria: elevation and azimuth. These values are measured in degrees.
Please note that in the process of regulation there are difficulties that are associated with the fact that, in accordance with the region where the equipment is installed, the indicators may differ and this is considered the norm.
For example, in Bryansk, the angle = 29 degrees, and the azimuth = 178 degrees. This feature should not be overlooked. Clarify standard specifications mono on the official website of Tricolor TV.
Setting up Tricolor TV on a Samsung Smart TV
In order to properly configure the equipment, you must first familiarize yourself with the process.
In this case, the model of the tuner, the size of the antenna, the quality of the equipment for synchronization, as well as the model of the TV are of great importance.
How to set up Tricolor TV yourself if the settings on Samsung Smart TV are wrong? If any interference or ripples appear, pay attention to the correct installation of the system. Measures must also be taken in the absence of channels that have previously been broadcast.
To do this, debug the received signal level as follows:
- Enter the system menu in the "Signal level" section and find the "Settings" option.
- Enter the password (default value is 0000) and confirm the actions to be performed.
- Go to " System settings” and click on the “OK” button.
- Select "Antenna settings" and select the list of channels, in accordance with the region of use: EUTEL SAT 36V or 36 A.
- Find 2 scales that indicate signal strength. They must be filled up to 70%. In this case, the work was carried out correctly, and no changes need to be made. In this case, attention should be paid to mechanical damage and adverse factors.
After completing the above steps, you can proceed to more fine tuning systems. Please note that the receiver must be registered if this procedure was not carried out during the conclusion of the contract. Otherwise, the equipment will not function.
Set up Tricolor TV by yourself video
So, as I wrote earlier, the classic way to connect satellite TV is as follows:
satellite dish- satellite receiver- television.
Benefits of using a satellite receiver:
For this method, you can use any TV, it doesn’t matter if you bought it a year ago or 10 years have passed, the main thing is to choose a cable to connect the satellite receiver and TV;
A satellite receiver can act not only as a satellite signal receiver, but also have other functions, for example: Internet access, Smart TV, DLNA, etc.
Cons of using a satellite receiver:
Inconvenience when using two remote controls (from the TV and from the satellite receiver). Although modern TVs use various technologies to connect all devices and use only the TV remote control (for example, Samsung-e's anynet + technology), such technologies do not fit all equipment and do not always work perfectly.
Connecting satellite TV using the CAM module.
Another way to connect satellite TV is to use the CAM module. CAM module(Conditional Access Module, Conditional Access Module) - electronic device used as an adapter for a particular encoding system to Common Interfaces on TVs and receivers digital television to provide subscribers with access to encrypted media content in digital television (Wikipedia).
To the majority modern TVs a satellite receiver (DVB-S2) is already built in, which only needs to add a device for decoding channels - a CAM module. Since each operator has its own coding system, each operator (Tricolor, NTV +, etc.) has its own CAM module. Thus, using the CAM module of a certain operator, you activate the receiver built into the TV and view the satellite channels of the selected operator without using an external satellite receiver.
Pros of using CAM module:
Control from one remote control. It would seem a trifle, but it is VERY CONVENIENT.
TV must support DVB-S2 and the Cl+ module. You can find out this information from the technical documentation for the TV or by saying the model of your TV when buying a CAM module.
How to connect and configure the CAM module?! In fact, connecting and configuring the CAM module is extremely simple and can be handled without the help of specialists. Below is a detailed description of how to install and configure the CAM module, it will be relevant for all popular operators - Tricolor, NTV+, Telecard, Rainbow etc.
Installation and configuration of the CAM module.
The first step is to correctly insert the access card into the CAM module. To do this, turn the access card with metal contacts up and insert it until it stops, while the CAM module should be facing you.
Then turn off the TV and insert the CAM module into a special slot (PCMCIA slot), usually located on the back side of the TV. The module must be inserted facing the wall.
Connect satellite dish to the TV.
After that, turn on the TV.
Before setting satellite channels, I recommend making sure that the TV "sees" your CAM module, for this go to the TV settings and look at the information about the CAM module. For example, on LG TVs, for this you need to go to "Settings" - "Quickly" - "Search for channels" - "CI data (CAM)"
After that "Module".
Select your module, in my case it is Tricolor CI plus CAM
And see information about it.
If the TV "does not see" the CAM module, then you have not inserted it correctly, turn off the TV and insert the CAM module correctly.
Setting up satellite channels through the CAM module.
Below I will describe how to set up the CAM module on an LG TV, for other TV models (Philips, Samsung, Sony, etc.) everything will be the same.
Go to the TV menu, to do this, press:
1) on a conventional TV remote control, the "Settings" button
2) on the magic remote control the "Input" button
and select the "Settings" button on the TV.
From the "Quick" menu, select "Search for channels".
Select "Auto Search"
Specify "Satellite" in the settings mode and click "Next".
From the list, select the operator whose CAM module you are using, in this case Tricolor.
If you are using the popular operator Tricolor, NTV+, etc., then in the next step just click "Next", otherwise click "Settings" and make the settings corresponding to your satellite operator.
The next step, click "Run" to start searching for channels. You can also specify a more accurate search by selecting, for example - Skip coded channels, etc.
An automatic search for satellite channels will start, you must wait a few minutes before it ends.
As a result, you will see the number of channels and radio found, now you can click "Finish".
As a result, you have set up satellite TV using the CAM module.
Video settings of the CAM module Tricolor, NTV +, Telecard, Raduga.
For satellite or cable television you need special equipment: a receiver and a smart card that will convert the incoming signal from the provider to the TV. But, if the TV has a CI connector, then you can do without a receiver. In CI, you can install the module itself with a smart card, and the signal decoding function will be performed through it. In the article, we will consider setting up the CI Tricolor module on an LG TV and how to install the CAM module correctly.
Often confused or perceived as synonymous with CI and CAM. CI (stands for Common Interface) is the connector into which the CAM module is inserted. CAM-module (Conditional Access Module - conditional access module) is an electronic device that performs the function of an adapter, or adapter. A smart card is installed in it, through which coded channels will be transmitted to the subscriber's receiver.
The CAM device must be selected depending on the encoding of the service provider. For example, to set up Tricolor, you need the DRECrypt module. There are digital broadcasting standards:
- DVB-T and DVB-T2 - terrestrial TV;
- DVB-C - cable TV;
- DVB-S and DVB-S2 - satellite TV.
CI can support either a specific standard or several. It all depends on the model of the receiver. If you are interested in satellite broadcasting, be sure to make sure that the TV's built-in tuner supports it. Now a little about the advantages and disadvantages of the CAM module in relation to the receiver.
Of the pluses can be noted:
- High transmission speed, since data processing takes place wirelessly, directly on the TV;
- Transferability maximum quality Images;
- No need for an additional remote control;
- Longer service life;
- lower cost.
Of the minuses, the following should be said:
- There is no possibility to watch TV programs;
- The functionality and interface are more limited in comparison with the set-top box;
- There is no possibility to show a large list of channels;
- The setup is more complicated (however, on LG TVs, the corresponding channels are automatically selected when you select an operator).
What is included
Tricolor TV Company provides a choice of several sets of equipment for smart and regular TVs. Most have receivers in their composition, but there are also those with a CAM module. This set includes:
- Tricolor CAM module, compatible with TV receivers that support the DVB-S2 satellite digital television standard;
- Tricolor smart card for TV;
- satellite dish;
- Satellite circular converter.
It is not necessary to take a ready-made set of equipment. It is important to purchase only the smart card of the selected service provider and conclude an appropriate agreement. Next, we will consider what requirements are imposed on the equipment for connecting the CAM module itself to the TV, as well as how to set up Tricolor TV on LG.
equipment requirements
The first thing that must be configured for the Tricolor user is an antenna that must catch the frequencies of one of the satellites: Eutelsat 36V, Express-AMU1, Express AT1. Then you don’t have to set special settings for the CI slot: everything will happen in automatic mode.
One more caveat: the slot must be CI+. This is a new version of the CI connector with reverse encryption. That is, before serving on the screen, all information will be encoded. This allows the provider to protect its data from copying. Now, not all content can be recorded from such a device, but only the content that will be allowed for recording. The TV must have an LNB IN port, which indicates the presence of CI + technology.
The TV must be equipped with a built-in digital tuner that supports the DVB-S2 satellite broadcasting standard. It is also desirable that the TV set supports 4K UHD (television ultra high definition) and HEVC (High Efficiency Video Coding Format). If such formats are not supported, channels broadcasting in the specified quality will not be available.
The CAM module must match the encoding of the smart card. The device is connected to the TV in the usual way: Inserted into the CI connector. If the TV suddenly stopped seeing the smart card, you need to check that the module and slot are connected correctly. After connecting to the connector, the authorization check will begin.
Sometimes the message about checking permissions may hang for a long time. To eliminate this, the time settings on the TV must be set to automatic. You can also try resetting the CAM module settings to factory settings.
The built-in tuner gives certain advantages over the receiver: there is no need to purchase a separate device that will take up additional space.
Connecting and configuring the CI Tricolor module on an LG TV
Now let's take a closer look at how to connect and how to set up the Tricolor module on LG TVs:
- The TV must be turned off before installation;
- It is necessary to insert the Tricolor card into the CAM module all the way with the contacts up, and the CAM module into the CI slot on the TV receiver. The antenna cable must also be connected;
- Turn on the TV and watch the information on the screen. An error message may appear. The card or module may not be fully inserted. You need to check the physical connection. To make sure that the TV sees your device, it is better to go to the CI (CAM) menu, where this information will be displayed;
- Now you need to go to the settings menu. Find items there Fast" and " Channels»;
- In the channel setting mode, select " Satellite» and press « Further»;
- Set the operator "Tricolor". The satellite must match one of the service provider's satellites. The settings are set automatically. The only thing you can check is the signal quality, which should be at least 70%. Its correction is done by adjusting the antenna and checking the connection of the cable and all other components;
- Now you can start connecting channels. To do this, go to the channel settings and perform an automatic search. How newer version software, the more complete the final list will be. After the search is completed, the list is saved;
- If everything went well and it turns out to open channels, you will also need to adjust the sound for old software firmware. To do this, you need to find Digital TV sound setup» and select « mpeg". AT latest versions firmware this problem is fixed;
- Now you need to perform a factory reset by selecting " CI data". This is necessary so that later there is no message that the access check failed. After that, turn off the TV from the power supply. This completes the CI setup.
If the automatic channel search does not give satisfactory results, you can manual setting. To do this, you need to select a satellite and set the frequencies of its transponder to 12 111 MHz or 11 881 MHz, as well as horizontal polarization. When manually searching, be sure to check the box " Network search».
On LG TVsthe default option is automatic search channels. It must be disabled, otherwise the channels you found will be reset.
After all operations, the TV is turned on again and left on for up to 8 hours. This is necessary to obtain service activation keys. In the CI data (CAM) menu, you can find information about the smart card: an identification number, connected packages and their validity period.
Another important point is updating the module software. Detailed instructions can be found on the Tricolor website www.tricolor.tv. Do not forget about the timely update of the version, as it is too old software products do not perform all available functions or may refuse to work correctly.
The current version of the module software can be found in the settings: " Information» -> « Module» -> « Software version» (item names may vary depending on the model). To perform an update, you need to do the following:
- In the module settings, it should set the current state of pop-ups in the status " activated" or " Included»;
Modern TVs do not need to connect additional equipment for a long time and are able to receive and process a signal from a satellite without connecting a receiver. Now, in order to watch satellite TV, it is enough to purchase the ci module offered by Tricolor.
This device allows you not to pile up the space of the apartment with unnecessary appliances, leaving it as spacious and elegant as possible. At the same time, the quality of broadcasts remains at the highest level, even when it comes to channels in Ultra HD. As a result, users get the maximum benefit from all possible sides. And the only drawback of such devices is an unusual setting that can cause difficulties for unprepared subscribers.
What is a Cam Module
Those who have not yet encountered Tricolor TV modules should know that given device are a portable analogue of standard receivers, designed specifically for smart TVs.
They are a small plate into which a smart card is inserted. It is this device that receives the signal from the satellite and decodes it to watch TV channels.
At the same time, those wishing to buy a cam module will have to think in advance whether the TV they are using is compatible with the new device. Additionally, it should be clarified whether signal reception is supported in the subscriber's region of residence. This information can be provided by official distributors of equipment or contact center consultants.
General information about setting up the Tricolor TV cam-module
Those who decide to do self-tuning you must know that, as is the case with most of the similar equipment, there are both universal devices and Tricolor cam modules that can only receive the signal of the mentioned provider. Professionals recommend purchasing equipment of the second type, since it is much easier to set up.
Additionally, you need to be aware of the differences associated with TV models. The procedure for connecting to satellite TV on LG and Samsung TVs has several differences that need to be considered. Further about them will be discussed in more detail.
Setting up the Tricolor ci module on a Samsung TV
Most of modern technology capable of automatic adjustment. If it does not start, you will have to manually configure the Tricolor with the ci module for the Samsung TV. For this you will need:
- select the User Sat1 satellite on the start page;
- then, in the LNB section, you will need to set the lower frequency limit, which must match the upper one;
- after which the user will have to switch to "channel settings";
- re-specify the satellite and click the “create” item in the “transponder” line;
- then you will need to specify the frequencies and speed (they are present on the website of the satellite company and in the instructions for the module);
- keeping set parameters, the subscriber will have to start the search.
For getting complete list later you will have to start the search again. This completes the Samsung smart TV setup, and viewers get the opportunity to watch TV channels.
Setting up the ci Tricolor module on an LG TV
Preparing for the operation of the Tricolor TV conditional access module on LG will be a little easier. Those wishing to watch satellite TV will have to:
- on the start page, set the basic parameters, indicating the type of antenna (satellite), converter (single), satellite (Eutelsat), frequency 12226, power supply (on);
- after saving the listed parameters, the user will be prompted to check the signal level (the reception quality should exceed 80%);
- the next step is to switch to the TV channel search section and start it automatically;
- then it remains to press the save button and adjust the sound in the appropriate subsection (should be MPEG4);
- The last step is to switch to start page and entering an activation code.
Sometimes, before entering the code, you need to reset the settings to the factory level. Otherwise, the equipment is ready for work and subscribers can already watch their favorite programs.
Problems and solutions
Despite the simplicity of preparing the Tricolor Ultra HD cam module for operation, some users are able to encounter sudden problems. They are usually caused by:
- incorrectly inserted smart card;
- equipment failure;
- user errors;
- incorrectly rotated antenna (the reception quality scale on the screen will be below 80%);
- non-compliance of the TV with modern requirements.
Clients of a satellite company are able to cope with almost every of these troubles on their own. So, it is often enough to check the connection and carry out the setup procedure again.
Sometimes you need to go to the module menu and reset the settings to the factory level.
In the most difficult situations, you will have to call the contact center consultants. But it is important to prepare information in advance that will allow them to recognize the caller. It includes passport data, connection address, service agreement number, smart card ID.
class="eliadunit">
First, reset the TV to factory settings. Menu> support> self-diagnosis> reset> ok. After the reboot, go to the menu> channel> antenna> select the value "satellite". (by the way, pictures with a preview - click to enlarge)
We remove the checkboxes from all the satellites that are set by default (if this fails, you need to pull the CAM module out of the slot and reset the TV again), scroll through and select Eutelsat satellite W4 36E, select the transponder in the LNB settings 12226 , lower gen. LNB- 0, top - 10750.
Then go to "manual settings", look for the transponder 12226, turn on "network search" and press "search".
Then you can sort the channels at your discretion (it is better and more convenient to do this with Samsung programs Channel List Editor)
If the satellite EutelsatW4 36E is not in the settings, do this:
Select "User sat 1".
We create our own satellite (put a bird in front of it) and save it.
We go into the LNB settings, set everything as in the screenshot.
We do not put anything in the "transponder" section, we will add them manually.
In the "transponders" section it will be empty, select "create".
We need transponder frequencies, bit rate and polarization type for each channel package. I will list:
Attention!!!
- The flow rate in all cases will be 27500, except for the frequency 12190 L for it - 20000.
- Not all transponders have polarization type (L), for 12054 (R)
Now we create all these transponders (continue).
We drive in the frequency (with numbers directly from the remote control), the transmission speed (also from the remote control) and select the type of polarization (L or R). Click "save".
The network name "Tricolor" appears, click "search" and "OK".
The package of channels for this transponder is scanned and stored in the TV's memory. Then everything is repeated for each subsequent transponder. In the same place, in the "manual setup" menu, click "scan" in the "transponder" section, create the next one with your data, and so on. All previous filled and scanned transponders with settings and channels are saved.
As a result, we get 238 (together with the radio) Tricolor channels.
