Instruction

Look at the instructions to find out the model of the storage device installed on your computer.

Go online. Type in the search "forum HDD". Explore the information on the forums where users discuss hard drive specifications, what programs they use to determine and adjust the spindle speed. Here are a few addresses of large sites where you can get help and good advice: ClubControl (http://www.clubcontrol.ru/forum/), HDD forum (http://hdd.kulichki.com/forum/), Monitor (http ://monitor.net.ru/forum/), etc. On the Internet, you can find a large number of programs, both paid and free. However, not all of them work equally well with different models of hard drives.

Download and install what you need software. Now turn off your computer and let it rest for 10-15 minutes. To determine the actual disk rotation speed, it is necessary to take measurements in a system that has not yet had time to receive a large load and is in perfect condition.

Run the program. View the list of physical drives, which are presented as a list or chart. Select the drive you want to know about at the moment.

Do a speed test called Benchmark. Usually, with the help of this test, it is possible to obtain information that gives a completely objective picture of the state of the disk as a whole. Click the Start button and wait for the testing procedure to complete.

Analyze the data collected by the program. Pay attention to several critical points. First look at the Transfer Rate Minimum value. This indicator determines the minimum data transfer rate, while Transfer Rate Maximum indicates the maximum. Then move on to an average speed called the Transfer Rate Average. Write down the numbers or save them in any other way.

Check Access Time - an indicator that describes the average file access time, which is measured in milliseconds. Together with Burst Rate (peak HDD rotation speed), Access Time is a very important characteristic to consider. Record also data on CPU load during rotation hard drive.

Compare all the data collected by the program with those provided by the HDD manufacturer in the computer's operating instructions. Pay attention to the fact that the numbers of indicators can differ significantly, but this does not always indicate a breakdown of the HDD. The conditions of its operation have a great influence on the test results.

Sources:

  • how to check disk speed

To test hard drives, a lot of paid and free programs have been developed. HDD Scan is a free program for Windows with which you can view S.M.A.R.T indicators, check the hard drive for bad sectors, and also see in graphical representation speed characteristics of the speed of the hard drive.

You will need

  • - a computer;
  • - the Internet;
  • - HDD Scan program.

Instruction

Download HDD program scan. It doesn't need to be installed. You can find the installer on the official website of the developer hddscan.com. Save the downloaded program to the Programs folder for later use and run the application by double-clicking on the start file.

In the main program window, in the Source Disk section, check if the hard drive is selected correctly. You can see the S.M.A.R.T data by clicking on the button of the same name just below. You can easily find the decoding of these attributes on the Internet.

In the Process area, click the Start button to start the disk check. The Start LBA parameter is the first sector of the test, and End LBA is the last sector. During the validation process, the Map tab area will be filled with colored squares representing sectors. As soon as the entire space is filled with such squares, the system will automatically notify you that the computer has fully checked the speed of the hard drive.

Click the Map tab to view the hard disk speed graph. It may differ depending on the area of ​​the sectors, which in this moment being tested. The program also offers to adjust the noise work hard disk, display data on checking sectors in the form of a report, and some other features. HDD Scan is fairly easy to use and worth having in your arsenal of computer maintenance utilities.

In general, we can say that it is not difficult to check the speed of a hard drive on a personal one, since it is enough to download the appropriate software and perform a few simple operations. However, be careful, as improper work with such programs can disrupt the entire system.

Related videos

Tip 3: How to determine the speed on the Internet in 2017

There are a few questions that beginner PC users have. The first question is how and with whom to connect the Internet, and the second is what type of Internet to choose in order to get a decent one. There are ways to determine what your Internet connection speed is. This lets you know what time of day the speed is the fastest, as well as how long it takes to download your favorite series.

You will need

  • Special sites for measuring internet speed online.

Instruction

First of existing methods- is to use special sites that determine the speed of the on-line connection. In order to do a check, you just need to type the address of one of these sites and it will show you all the necessary data in the form of a table "test results for".
In this case, the data will be real, such that your Internet site really provides. Indeed, for many it is no longer a secret that the download speed may also depend on the width of the channel of the resource from which you are downloading.

In order to get more reliable data about the check, you need all the programs that can affect the result of the check itself. These are programs such as flashget, emule, reget and bittorrent. The same goes for radio and the internet. It is advisable to repeat the test several times - for a more accurate result. There is nothing complicated, but you will find out the real data about your Internet connection.

Before starting the verification procedure, you need to indicate the speed declared by the provider - this is necessary in order to compare the real speed and the promised one. It takes very little time to check - only 30 seconds. This is quite enough to determine the speed. The site reports how many meters it passed in those 30 seconds and how it determined the speed.
How alternative way can be used special programs to check the speed of the Internet - but this is already a surplus of the past, it is much easier to check online sites. The data will be more accurate, and you will know how long you can watch a movie, favorite or picture.

Related videos

Useful advice

Services for determining the speed of the Internet: http://2ip.ru
http://spchat.ru

When downloading a certain file from the Internet, it is interesting to know about the speed, as well as the time that will have to wait until the entire operation is completed. This can be done using special software.

Instruction

There is a large list of various software on the Internet that allows you to see in real time speed transmission data. One of the popular utilities is Download Master. This program spreads completely. You can find it on the Internet or install it from the disk containing the distribution kit of the operating system with the installation of programs in WPI mode.

Install this software on the hard disk of a personal computer. For convenience, install to the system local drive so that the program and all downloads are on the same local drive. In the event of an emergency, you can backup and quickly recover information without any loss. A shortcut will appear on the desktop with which you can open the main program window.

An icon will also appear in the tray, which, when new download will display the current process. Open the program by double-clicking on the shortcut with the left mouse button. In the browser, find the file you need to download. Right-click on the link and select "Copy link address" from the context menu. The download is automatically integrated into the program window. You only need to click the "Download" button.

This software allows you to download up to 10 downloads at the same time, but the list of pending files can be endless. Opposite each downloaded file will be displayed speed downloads, as well as the time it will take to complete. At the top of the program there is a small graph that displays the maximum and minimum speed download all files. You can leave a description for the file, so that later you don't get confused with a large volume of files.

Related videos

The higher the quality of the communication channel, the more comfortable the work on the Internet. Pages open very quickly, even large files are downloaded in a short period of time. However, even when good channel the user sometimes has a desire to find out the real speed transmission data.

Instruction

Use special network services to evaluate your channel. They work according to the following principle: a small file is transferred to your computer, the time spent on its reception is measured. Based on this information, it is calculated speed receiving data. For example, follow this link: http://ip-whois.net/test-speed-internet/ Select any server on the map, click it with the mouse. In the window that appears, click the line "Start the Internet." Testing takes less than a minute, after its completion you will see the results of the test.

You should know that speed Internet coverage is highly dependent on the time of day - it is worst when the lines are busiest and increases when most users are offline - for example, at night. Therefore, conduct this test several times at different times of the day, this will help you find out how the speed internet during the day.

You can appreciate the real speed your internet while downloading large files- for example, files from , DVD images, etc. The download manager usually says speed transmission data per second. Please note that providers indicate speed internet in kilobits.

Related videos

A slow-running computer can piss off even a very calm person. It is not necessary to change a slow machine to a new one - it is enough to find out which particular component reduces its performance and upgrade.

Instruction

There are two reasons for performance degradation computer: insufficient computing power processor and too little random access memory (RAM). The second of these reasons reduces speed work indirectly: when a resource-intensive application that is not running is running, it starts using the hard disk for temporary data storage. This process is called swapping. Communication with hard drive is much slower than with RAM. To determine what exactly needs to be upgraded, look at the hard drive activity indicator. If the “braking” of the machine is accompanied by active access to the drive, it is necessary to increase the amount of RAM, and if not, replace the processor.

Greetings!
The speed and performance of the entire personal computer as a whole depends on the performance of the disk (HDD, SSD)! However, to my surprise, a fairly large number of users do not attach due importance to this aspect. And this despite the fact that the speed of loading the operating system, launching programs, copying files and data from the disk and back, etc., directly depends on the storage medium. In other words, a fairly large number of typical operations on a PC are tied to the memory subsystem.

Now in computers and laptops, either traditional HDDs (hard disk drive - HDD), or the recent trend - SSD (solid-state drive - solid state drive). Often, SSD drives are significantly faster than classic ones in read / write speed. HDD drives. For example, Windows 10 starts up in 6..7 seconds, compared to 50 seconds from a regular HDD - as you can see, the difference is quite significant!

This material will be devoted to ways to check the speed and performance of the installed HDD or SSD drive.

Overview of CrystalDiskMark

Quite a popular measurement and testing utility HDD speed or SSD drive. She works great in Windows environment(XP, Vista, 7, 8.1, 10) is free and supports the Russian interface language. Official website of the program: http://crystalmark.info/

To test an HDD or SSD in CrystalDiskMark, you need to do the following:

1) Select write/read cycles. By default, this number is 5 , which is the best option.

2) After that, you need to select the size of the file to be recorded during the test. 1 GiB(1 Gigabyte) will be optimal.

3) And finally, you need to select the partition that will be used to test the disk. If you have several physical drives installed, then select the partition that is located on the drive you are interested in. In the example, there is only one installed hard disk and the partition is selected accordingly C:\.

4) Click the green button to start the test All. By the way, in the overwhelming majority of cases, the result of interest is what is in the line SeqQ32T1– linear read/write speed. You can start testing only the read/write linear speed by clicking the corresponding button.

Test results will be displayed in columns:

read– a parameter showing the speed of reading data from the tested disk.

Write- a similar parameter, but showing the speed of writing to the tested hard disk.

On the Kingston UV300 SSD tested in the example, the linear read speed was 546 MB / s - which is a very decent result. In general, for the best representatives of SSD drives, this parameter varies around 500 .. 580 MB / s, taking into account the connection to the SATA3 connector on the motherboard.

If the speed of your SSD drive is significantly less than that declared by the manufacturer, then it makes sense to check if it is connected to SATA3.

How to determine the version and mode of the SATA port

The developer of CrystalDiskMark prudently created another diagnostic utility - CrystalDiskInfo. Its task is to display S.M.A.R.T information about the state of the disk, its temperature regime and other parameters.

In general, a fairly convenient and visual utility that should be in service with users who care about monitoring the state of the disk (its health) in order to avoid data loss due to its possible breakdown.

After starting the utility, look at the information that is displayed in the line " Transfer mode»:

SATA/600- means that the disk is operating in SATA3 mode with a maximum throughput of 600 MB / s.

SATA/300- this parameter means that the disk is operating in SATA2 mode with a maximum throughput of 300 MB / s.

It may still shine SATA/150(150MB/s) is the first SATA version standard and it is considered very outdated and does not meet modern requirements for the throughput of connected media.

Whereas a classic HDD is enough SATA2(300MB / s), then the SSD must be connected to the port SATA3, otherwise he will not be able to reveal his full speed potential.

Overview of AS SSD Benchmark

I present to your attention another remarkable utility, the task of which is to test the speed of installed on a computer or laptop hdd or SSD drive. With it, you can just as easily find out the speed characteristics of the connected disk.

The utility is free, does not need to be installed and works in the Windows environment. Official website of the program: http://www.alex-is.de/

Management is carried out in a similar way to the CrystalDiskMark program. Linear reading speed is displayed here in the graph Seq.

Overview of HD Tune

The HD Tune utility completes this review. The capabilities of this program are not limited to testing the read / write speed. Among other things, it also allows you to control the health of the hard drive, its technical specifications and even scan the disk surface for errors.

If we focus on the possibilities of speed testing, then the following can be noted here:

  • the ability to separately set write or read testing
  • convenient visual chart of write / read speed during testing
  • ability to see peak speed and access time

The program works in the Windows environment and provides convenient tools for monitoring and testing connected media.

Official website of the program: http://www.hdtune.com/

Summary

The speed of the connected media directly affects the overall performance of your computer or laptop. Do not neglect the control of speed characteristics, because the overall comfort of working with a computer depends on it.

Now you know how to check the speed of the connected media, as well as the possible nuances of its connection, on which it ultimately depends throughput connected HDD or SSD.

But there is a direct dependence for the performance, speed of the entire computer. It also depends on the speed of loading the OS, and launching programs, and copying files, exchanging data, and more.

The hard disk speed test by this utility is performed in this order.

  • In the program window, select the number of write, read cycles. 5 is optimal.
  • Indicate the file size, 1 GIB is recommended.
  • Select a hard drive letter (C:).

Crystal Disk Mark Setting

  • Press the "All" button to start testing.

The program will show the speed of the hard disk - reading information, it will be in 1 column - Read. In the second column you will see the speed of writing to the hard drive. For an SSD, it is considered optimal from 400 Mb / s if it is connected via SATA3.

To save the results of the performance test, take a screenshot or select "Copy test results" in the "Edit" menu, a text report will be automatically created.

AS SSD Benchmark

An excellent utility that allows easy, quick testing of the hard drive. You don't need to install the utility. It should be used according to the same algorithm as in the utility described above.

A program that performs a hard drive test. It has free version and paid (Pro). The paid version without registration has a demo period of 15 days.

  • Run the program.
  • Go to the "Benchmark" tab, select the mode in which the test will be performed: "Write" or "Read".

  • If your computer has multiple hard drives, mark the one you need to check.
  • Click "Start" to start the test.

After completing the test, the program will show the results in numbers and graphs. You will find out the following indicators of data transfer speed:

  • Minimum - the smallest;
  • Maximum - the largest (usually it is what manufacturers say);
  • RateAverage - average;
  • BurstRate - peak (often given as real speed, but under normal conditions it is not always achieved);
  • CPUUsage - load CPU during testing.

After completing the test, having learned the results, you will probably wonder how to increase the speed of data exchange with the disk. After all, if the speed of data exchange with the disk decreases, and there can be many reasons for this, you need to make the computer act faster. There are several ways to speed up the speed of the storage drive.

Often owners personal computers faced with the need to check the speed of the hard drive. Usually this is due to the desire to find out how much the speed of reading and writing data to the disk declared by the manufacturer / seller corresponds to reality.

Agree, no matter how powerful the central processor is and how many gigabytes of RAM are installed in the system, it will not be comfortable to work due to the slow speed of the hard drive.

Note! If you want to get objective results, the amount of employed disk space should not exceed 80-85%. It also makes sense to disable resource-intensive applications - the browser, graphic editor, players, various utilities that often access the hard drive. All of them can affect the performance for the worse.

Consider several effective methods for testing the speed of a hard drive:

Option number 1 is a specialized CrystalDiskMark utility.

Now it is the most popular tester. It is convenient, functional and allows you to test not only ordinary HDDs, but also SSD drives. The user can choose from four types of tests - single-threaded sequential read and write, random read and write, and other options.

If you need to determine the actual read / write speed in order to compare with the data declared by the manufacturers, you should rely on the results of the "Seq" and "Seq Q32T1" tests.

Option number 2 - HD Tune program.

It comes in two versions - basic and advanced paid, but the first option is enough for the test.

To run the test, you need to go along the path to the “Benchmark” tab and select one of the options: reading (Read) or writing (Write), then click on the start button.

After the end of the test, data will be displayed on the average read / write speed, maximum and minimum speed, file access time, CPU load during testing.

Use the two above software product not necessarily, because on the network you can find their equally high-quality counterparts that differ from each other in functionality. Some applications, for example, allow you to get information about hard health disk, roughly predict how long it will last.

Option number 3 - testing in work. This the way is fine unpretentious users for whom the numbers are not important, but it is only important that the hard drive meets their needs. It shows the quality of the hard drive well, unpacking large files with an archiver, downloading using torrents, resource-intensive 3D games and applications. But there can be no question of any accuracy in all these cases, since other components of the PC can significantly affect the tests - the processor, RAM, video card, Network Card(in the case of downloading from the network).

Hi admin! Decided to buy a solid state drive the other day! I came to a computer store and I told the seller:

Sell ​​me the fastest SSD!

and they answer me:

Here you go, Kingston HyperX 3K (120GB, SATA-III) 555MB/s speed, superb SSD, you can't go faster.

Prove it!

Apparently they wanted to sell me this SSD so much that they installed it on a computer and ran a test in the CrystalDiskMark program, then showed the test result, here is a screenshot:

The sequential read speed is 541 MB / s and the write speed is 493 MB / s, I even took a picture of it on my phone.

In short, I bought this SSD, came home, connected it to my computer, then downloaded and ran the "CrystalDiskMark" program and ran the same test, but the result was worse!

489MB/s sequential read and 127MB/s write. Why?

In the store, the test was carried out on a computer with an Intel® Core™ i5 processor and 4GB of memory, but my computer is more powerful and is based on Intel processor® Core™ i7 and has 8GB of memory.

Explain to the admin what the catch is, otherwise I won’t sleep, after all, this SSD costs 3 and a half rubles.

Hi all! Yes, this can be friends, you just need to be able to use the CrystalDiskMark program. Now I will show you everything.

  • Note: You may be interested in our other SSD articles

The SSD test will be carried out in CrystalDiskMark 3 0 3

The program can be downloaded from the official website http://crystalmark.info/download/index-e.html

CrystalDiskMark tests our SSD like this:

All: All 4 tests run (Seq, 512K, 4K, 4K QD32);

Seq: Sequential write/read test (block size= 1024Kb);

512K: Random write/read test (block size = 512Kb);

4K: Random write/read test (block size = 4Kb);

4K QD32: Random write/read test (block size = 4Kb, queue depth = 32) for NCQ and AHCI;

Final result.

First, properly test the solid state SSD drive or any other hard drive! The fastest SSD will read and write information to the area filled with zeros alone. To do this, in CrystalDiskMark, in the file menu, select File->Test Data->All 0x0000 (Fill).

I also have this SSD SSD Kingston HyperX 3K (120 GB, SATA-III) and now I will do a simple test.

AT operating system SSD drive under the letter D:, so in the program settings select the letter D: and click

The Sequential Read/Write test of our SSD begins!

In a minute we get the result. Sequential read/write speed 543 MB/s (read), 507 MB/s (write)

Now we test differently. File->Test Data->Default (Random)

A minute later, we get a result that is not at all the same as when testing with the All 0x0000 (Fill) option. Sequential read/write speed 499 MB/s (read), 149 MB/s (write)

It is also important for the good performance of the SSD to properly connect it to your motherboard. All SSDs have a high speed SATA 3.0 (6 Gb/s) interface, and your motherboard probably has such connectors. For example my motherboard ASUS P8Z77-V PRO has four SATA 6 Gb / s ports and they are appropriately labeled SATA 6G, so we connect the SSD according to the marking.

To connect a SATA 6 Gb / s SSD interface, use the native SATA 6 Gb / s data cable!