Content

Many providers provide access to the network, but Beeline is considered one of the popular options. The company provides mobile 4G Internet or home connection. You can set up a connection through a branded modem or router from another company to get Wi-Fi coverage. Configuration may vary due to device model.

Setting up a router for Beeline

When using multiple computers at home, it becomes actual task set up Wi-Fi. Wireless Internet is especially convenient with modern smartphones, tablets or laptops. Setting up Beeline through a router can be done automatically or manually, it depends on the device model. As a rule, when concluding an agreement, a wizard comes home to help create a connection. If the installation of Wi-Fi was carried out later, or the device was replaced, then you will have to set up the connection again.

For each device there is an instruction for setting parameters for correct operation, but there are points that are the same for each case. For example:

  • connect the wire (cable) to the router;
  • connect the device through the second wire to the computer;
  • configure the device (drive in the address of the Beeline router, set the type of connection, set a password and protect the connection).

Setting up a Beeline DIR-300 router

There are several popular models of devices that are used by most customers. Few people take options without Wi-Fi, because, as a rule, the device is purchased for it. Setting up a router Beeline dir takes place in two stages: physical connection, connection management via browser. First you need to make sure that the network card is set to latest version firmware. This is more true for owners of older computer models. The configuration is then carried out as follows:

  1. Unpack the device, connect the power supply, the cord into the connector labeled "WAN". Connect the second cord to one of the additional inputs and bring it to the computer.
  2. Next, set up the connection in the Start menu. Go to the "Control Panel" item here click on "Network Control Center ...". Click "Adapter Options". Set the line to Internet protocol version 4, then click "Properties".
  3. Make sure that the items with automatic issuance of IP and DNS servers are active.
  4. Next, you need to go to the internal interface. To do this, in any browser, type "192.168.1.1" into the site address field. A login/password form will be displayed to enter the admin panel. To go inside, you need to enter the word "Admin" in both fields. These are factory access options, if they do not fit, then they have been changed. You can reset the values ​​by holding down the Reset button on the device. Hold for about 10 seconds.
  5. When you enter the backend, select "Manually Configure". Next, go to the "Network" tab, click "Add".
  6. Select connection type - L2TP, dynamic IP.
  7. In the appropriate fields, enter, issued by Beeline, login, password.
  8. Check the boxes next to "Keep Alive" and "Connect automatically". Click Save.
  9. Click "Save" again. Next will happen automatic connection. To find out about the correct operation of the network, just go to any site from your phone.

Setting up an Asus Beeline router

Another popular device manufacturer is Asus. There is no program on the disk for automatically connecting to the network, so you have to do everything manually. Carry out setup Asus router Beeline is needed as follows:

  1. Connect the device to power, network and computer.
  2. Open the browser, write in the address bar of the site 192.168.1.1, press enter.
  3. For access, enter the password and login "admin".
  4. In the back end, click on the "Advanced Settings" tab, select "Wan". Next, specify the following data: "Connection Type" - "L2TP", "Get the WAN IP automatically" - "Yes", "Connect to DNS Server automatically" - "Yes", " VPN Server- "tp.internet.beeline.ru". In the login / password fields, specify the accesses issued by the provider.
  5. To turn on Wi-Fi, go to the “Network Map” item.
  6. A quick configuration table will appear on the right. wireless connection. You need to configure it as follows: "Wireless name" - specify / think up a name home network, "Security level" - "WPA-Auto-Personal", "WPA Encryption" - "TKIP+AES". On the line "WPA-PSK key" write the password for Wi-Fi. Click the "Apply" button.

Setting up a TP-Link router for Beeline

This is a popular model due to the presence of an installation wizard that is able to connect to the network on its own. As a rule, a disk is sold with the device, on which the program is located. You just need to connect the router to your computer, insert the CD and run the application. If the connection does not open, you need to do everything yourself. Setting router TP-Link for Beeline is carried out as follows:

  1. After connecting the device, go to the browser, type "192.168.1.1", press "Enter". Enter login/password "admin"
  2. Open the "Network" tab and the "WAN" item.
  3. Specify the type of connection "L2TP", enter the login / password that your provider (Beeline) issued, the IP server - "tp.internet.beeline.ru".
  4. Specify the automatic connection ("Connect Automatically"), the MTU size is 1400. Click on the "Save" button.
  5. To enable WiFi networks you need to go to the "Wireless" section, click on the "Wireless Settings" item.
  6. Come up with a name for the network, specify the region "Russia", the channel and the mode - "automatically". Click the "Save" button.
  7. Next, go back to the "Wireless" section, click on "Wireless Security".
  8. Here, activate the item "WPA-PSK / WPA2-PSK", then everything is on the "automatic" mode. Create a password for the connection, click "Save".

Setting up a Zyxel Keenetic router for Beeline

Some users prefer Zyxel. The physical connection of the router is carried out in the same way (wire to the WAN connector and the second to network board computer). The internal network setting of the Keenetic Beeline router is as follows:

  1. Type in the browser line 192.168.1.1.
  2. Enter "admin" as username/password.
  3. Go to the "Internet" section, click on "Connection".
  4. Specify the following values ​​in order: think of any name for the router, set the IP settings and get DNS automatically, check the box to answer ping requests and enable UPnP. Click on "Apply".
  5. Next you need the "Authorization" tab. Do not check the first item, the protocol must be L2TP, the server address is tp.internet.beeline.ru, write down the granted accesses in the login and password lines. Save your changes.
  6. To activate Wi-Fi, open the "Wi-Fi network" section, the "Connection" section.
  7. Check the box to enable the hotspot. Come up with a network name, the SSID field must remain empty, the standard is 802.11g / n. The next two items should be in the "auto-select" mode, then leave everything as it is. Click on "Apply".


All cellular companies offer access to the worldwide network, but Internet access from the Beeline provider is considered one of the most popular options. The operator provides its customers and how Mobile Internet, operating according to the 4G standard, and home.
To get wireless Wi-Fi coverage, branded routers from other manufacturers are used, the settings of which vary depending on the device model. It is about how to connect a Beeline router that our today's article will tell.

Article content

  • 1 Set up a router from Beeline
  • 2 How to set up a router D-Link DIR-300
  • 3 Asus devices
  • 4 TP-Link devices
  • 5 Zyxel devices
  • 6 Conclusion

Setting up a router from Beeline

If several computers are used in one house, then the Wi-Fi setup becomes more than relevant. Internet access without wires is extremely convenient when working with modern smartphones, tablet PCs or with laptops. Setting up Internet access through a router can be carried out automatically or in manual modes, which directly depends on the model of the device used.

Basically, when signing an agreement with the Beeline provider, a company specialist comes to the new client's home and sets up the correct connection. But if wifi router was purchased later, or the device was replaced, the connection will need to be configured again.

Each router has its own manual for entering configuration parameters, but the individual steps are absolutely identical for all devices, for example:

  • Connecting the cable to the router itself.

  • Connecting a second cable directly to a laptop or PC.

  • Entering the correct settings (device address, type of connection used, setting a password, etc.).

    • Router connection diagram

    How to set up a D-Link DIR-300 router

    There are such well-known models of routers that most of all consumers use. This model is the DIR-300. Few of the subscribers choose devices without Wi-Fi, because, basically, only because of him the model is bought.

    Setting up the D-Link DIR device is carried out in two stages:

  • Physical connection (Fig. 1).

  • Managing the created connection through the browser.

    • First you need to make sure that the network adapter the latest version of the driver is installed. This mostly applies to owners of old PCs.

  • You need to unpack the device and connect the power supply to it, and then connect the cable to the port labeled WAN. The second cable is connected to any LAN port on the router and, accordingly, to the computer.

  • Next, the subscriber needs to open the "Start" tab on the PC and go to the "Control Panel" section, and then enter the "Network Control Center". Here you need to click on the "Adapter Settings" column and set the protocol version to the line "4", and then open "Properties".

  • The user needs to make sure that the "IP" and "DNS Server" items are in the "Automatic" mode.

  • Then the subscriber needs to go to the internal menu. To do this, enter the value 192.168.1.1 in the browser line and confirm the transition. A special form will appear in which you need to enter a login and a security password. To get to the admin panel, you need to enter the word "Admin" in both lines. This is the factory method for gaining access.

  • In the interface that appears, select the item " Manual settings”, enter the “Network” section and press the “Add” button.

  • Then set the connection type to "L2TP", and set the IP to "Dynamic".

  • In the fields that appear, enter the client's login and security password. They are issued by Beeline when buying a router.

  • Then you need to check the boxes next to the items "Automatic connection" and "Keep Alive", and then press the "Save" key.

  • Press the "Save" button again, after which the connection will be made in automatic mode.

    • Everything - the router is configured.

    Asus devices

    Another well-known manufacturer of routers is Asus. On the disk attached to the device, there is no utility for obtaining settings in automatic mode, and therefore the subscriber will have to register all the parameters manually.

    ASUS router

    You need to enter the settings for the Asus router in the following way:

  • The device must be connected to the network and connected directly to the PC using the supplied cable.

  • Then you need to open any browser and enter the value 192.168.1.1 in the search bar, and then press enter.

  • To gain access, the user needs to enter a login and a security password - you need to enter the word "Admin" in both fields.

  • After entering the internal interface, you need to go to the tab called "Advanced Settings" and select the "WAN" column. Then we set the connection type to "L2TP" and make sure that the "IP" and "DNS Server" items are in the "Automatic" mode. In field " VPN server»We prescribe such an address - tp.internet.beeline.ru. You also need to enter your own login and security password - they are issued to the subscriber when buying a router.

  • To activate Wi-Fi, you need to go to the "Network Map" tab.

  • On the right side, a table with a configuration for a fast wireless connection will be displayed. The parameters here must be entered as follows: "Connection name" - come up with any; "Type of protection" - WPA auto; "Encryption WPA" - enter "TKIP + AES". In the "Password" field, you need to enter any invented, if necessary. Then click on "Confirm". Now the router is fully configured and ready to go.

    • This completes the setup of the router for Beeline.

    TP-Link devices

    This device model is quite popular and in demand due to the fact that it has an installation wizard that can connect to the network automatically. Basically, a disk is supplied with the router, on which the master is located. The user only needs to connect the device to a PC, insert a disk into it and run the installation wizard. If, for unknown reasons, the connection could not be established, then there is only one way out - entering the parameters in manual mode.

    TP-Link router

    The device is configured as follows:

  • After connecting the router to the PC, the subscriber needs to go to any browser and enter the value 192.168.1.1 in the line, and then press enter.

  • Next, go to the "Network" tab and open the "WAN" column.

  • Then we set the connection type to “L2TP”, enter our login and the security password that was issued by the provider when buying the router, and for the IP server we prescribe the following address - tp.internet.beeline.ru.

  • We indicate "Automatic connection" and for "MTU" we set the value to 1400. Then we press the "Save" button.

  • To activate Wi-Fi, you need to go to the "Wireless" section and open the "Settings" column.

  • Next, we come up with a name for the network being created, set the region to Russia, and also set the value “Automatic” for the “Channel” and “Mode” items. Click on "Save".

  • Next, go to the "Wireless Security" section and activate the "WPA-PSK" item. For all other items, set the value to "Automatic". Press the "Save" button. The router is now fully configured.

    • Zyxel devices

    Some customers prefer to use devices from the manufacturer Zyxel. Let's look at how to set up a router from this company. They connect to the computer in the same way as the above devices. But the internal configuration is carried out in this way:

    Zyxel router

  • We go into the browser and enter the value 192.168.1.1 into the line.

  • Enter the word "Admin" in the fields for the login and security password.

  • Then go to the "Internet" tab and click on the "Connection" column.

  • Next, fill in the following items: the name of the Internet center - enter any; set the “IP” and “DNS Server” items to the “Automatic” mode; Opposite the item "Ping requests" put a tick and set the value of UPnP to "Allow". Press the "Apply" button.

  • Then we go to the "Authorization" tab and set the connection type to "L2TP", and for the server we prescribe such an address - tp.internet.beeline.ru. In the fields for the login and the security password, we prescribe those accesses that were issued when the device was purchased. Press the "Save" button.

  • To activate Wi-Fi, you need to go to the "Wi-Fi Network" section and select the "Connection" item. Then check the box next to the "Connection points" item and come up with a name for new network. The field with the name "SSID" is not filled. We set the standard to 802.11g / n. The next two sections are switched to the "Automatic" mode. Click on "Application".

  • Next, go to the “Security” tab and set the value to “WPA-PSK” for authentication, set the value to ASCII for the format. If necessary, we come up with a password for the network. At the end, click on the "Apply" button. Now our router is fully configured and ready for the first connection.

    • Conclusion

    We examined all the most popular models of routers for Internet access from the Beeline cellular company, and also talked about how to connect them and configure them correctly.

    In fact, setting up a Beeline router should not cause any problems for users. All that is needed is just to repeat all our actions in practice and positive result won't keep you waiting long.

    Recently it has become widespread network devices, supplied by one or another wired Internet operator, that is, a provider. Of course, the equipment is not produced by the provider, for example, the D150L WiFi router supplied by Beeline is a device manufactured by D-Link under the name DIR-300NRU. And so on. Only the firmware differs in two “different” devices, moreover, not very much. Let's take a look at the setting.

    If there is a router available that is on the recommended list (in this case, by the Beeline operator), then on the Web you can find instructions for setting up an Internet connection. Turn on and WiFi setup- always considered in the "manual" attached to the device, which should also be on the official website of the company that produces routers. We will look at how to set up a Beeline D150L router, which has a customized given operator firmware option, and then, setting up an Internet connection - we will repeat on the "regular" DIR-300BRU "D-Link".

    Modern network harvesters "Beeline"

    There is a point in purchasing devices with customized firmware. But it seems to only have it if the user "connects" to a single operator. Not everyone is able to set up an L2TP connection, and this is the protocol used by Beeline.ru. Setting up a Beeline router equipped with operator firmware will be trivial (of course, if you use the services of the Beeline.ru provider). Actually, setting up a connection here will come down to specifying a login with a password (see an example):

    D150L Router Configuration Interface

    In addition to the "Save" button, we see next to it: "Advanced settings". By pressing this button, we will get access to the router settings, the same as those provided in D-Link devices. That is, in theory, a customized router can be connected in the future to any provider. But - do not rush to choose. New firmware released by the equipment manufacturer (D-Link, for example) appear more often, which is important.

    Wi-Fi router Beeline D150L is completely similar in its functions to the DIR-300NRU device from D-Link. Now we will look at how to connect and configure the router if it is equipped with Beeline firmware.

    Connecting and logging into the web interface

    Preliminary steps before setting up

    The router must be connected to the network card of the computer (using a patch cord). The Internet port, installed separately, is designed to connect the provider's network cable. After completing the cable connections, you can turn on the router.

    Router hardware connections

    It must be remembered that the Beeline Wi-Fi router (or D-Link) must boot after being turned on. Which takes 30-40 seconds. During this time, you can have time to check the network card settings on the computer:

    Setting up a wired connection in a PC

    You need "Auto" DNS, "Auto" IP. If the network card is configured correctly, it remains only to restart the computer. The next step is to go to the graphical web interface. It is better to perform any configuration steps from a PC that is connected to the device via a patch cord (and not via Wi-FI).

    Connecting to the web interface

    Open the browser on the computer, go to the address 192.168.1.1. The firmware installed on the Beeline WiFi router is equipped with this address value.

    Login to the web interface

    As a login with a password, the “admin” pair is suitable here. Previously, in the devices of this operator, the login with the password "beeline" was used, but D-Link routers use the "admin" login by default. The user should not have any problems setting up a "proprietary" router, but at the same time, the "improved" Beeline version should not differ too much from the prototype. This logic can be described as follows: “the same, plus something else”, which will allow you to quickly and easily set up an Internet connection. Of course, if we are talking about a separate provider, in this case, Beeline (but no more).

    Setting Basic Functions

    Internet connection in Beeline routers

    If we consider only the Beeline Internet, setting up the D150L router is not very difficult. Having entered the web interface, the user sees the start tab, where it is enough to set the subscriber's login and password (then click "Save"):

    In addition to specifying the data, you need to decide whether you plan to watch IPTV through a computer (or through a set-top box). If yes, then in the line "TV on PC" it is better to immediately correct the value "No" to something else. You can specify "port for set-top box", but then the value "No" remains. Simple IPTV setup- Another "plus" of customized firmware.

    In any case, the Beeline router is configured for the L2TP protocol used in the network of this provider. A minute after the "Save" button is pressed, the connection should appear.

    Additionally, note that the connection appears immediately after the automatic saving of parameters in permanent memory router. After setting up the connection, the user is not required to reboot the device (which is true for any DIR-300NRU firmware, and is a feature of the hardware circuit).

    Setting up an Internet connection in routers with D-Link firmware

    Which router is better for Beeline - with customized firmware or regular? Going to the "Advanced settings" D150L, ​​we will see a graphical interface that completely repeats the set of tabs of the DIR-300NRU router:

    Router web interface

    To configure the connection, you need to go to the specified tab ("Network" -> "Connections"). All unnecessary connections, except for LAN, can be deleted, and then you can start setting up the connection “via IPoE” (by clicking “Add”). By default, everything is configured correctly, you only need to check the IGMP checkbox if you are using IPTV.

    At the next step, the L2TP connection is configured, below we give an example of the setting for Beeline:

    Setting up L2TP Beeline

    Having set the values ​​​​on a particular tab, click "Save" (the button is located at the bottom right). When setting up L2TP, you must specify the subscriber's password and login, and the server name.

    It is important to know that the web interface address in D-Link routers is usually 192.168.0.1 (for Beeline firmware, it ends as “1.1” or “10.1”). And the password in such routers is “empty”.

    Change Wi-Fi network settings

    How to set up a Beeline router to work wireless network, and how can I disable the password in it, or return it again? For fine tuning Wi-Fi networks, the start tab of the D150L router is not intended. Therefore, select "Advanced Settings" to go to the "Network" -> "Wi-Fi" tab:

    Wireless settings tab

    For the Wi-Fi network to work, the "Enable ..." checkbox at the top of the page must be checked.

    If you need to work "on a hidden name", you need to "Hide access point". Next, the network is configured as follows:

    1. You need to set the network name (SSID text box)
    2. Country, number of clients, channel number - leave "by default"
    3. Wireless mode - you can leave "B / G / N" (the network will be "seen" by any subscriber devices). Also, if all subscribers work using the modern 802.11 N protocol, it is recommended to set the “N Only” mode.

    After completing the settings, you must click "Change". Then you need to save the values ​​\u200b\u200band reboot the router. Find in top menu"System" item "Save. and Reload.

    Enable or disable Wi-FI encryption - you can in the next tab: "Security Settings". If you select “Open” in the first drop-down list, you can enter the network without a password:

    Encryption settings tab

    Nevertheless, we recommend using network security, for which WPA / WPA2 mixed PSK authentication and the AES algorithm are suitable. The key must be set in the corresponding field. After setting - you need to click "Change", save the settings, reboot the router. How to connect a Beeline router to the Internet - we have considered, so successful routing!

    What to do if you do not want to buy a router from Beeline

    If the connection of the Beeline provider will be used, the easiest option is to purchase "adapted" equipment. But as we have already said, routers with Beeline firmware, except for options that simplify configuration, do not differ from their “prototypes”.

    The first conclusion is that you can buy a similar router in a store that is compatible at the hardware level with the Beeline device. Then, you can even install customized firmware, which is available on the Beeline website. The latter is true for all users (and not just for owners of an "adapted" router).

    And yet, which router to choose for Beeline? Previous option fraught with two problems: firstly, the warranty terminates immediately after installing a firmware that differs from the “branded” one. But if the guarantee is of little interest, there still remains a question that is rarely paid attention to.

    A "suffix" is usually added to the name of a branded router, for example "DIR-300NRU". It means the revision number. It could be A1, B2 and so on. The main thing that we should note here is that the 300NRU A1 and 300NRU B2 routers are different, not compatible with each other. This is true for all models of any firms, and for any revisions. That is, firmware from one hardware revision is not suitable for the rest. Will the user be able to find out which revision it belongs to best router for Beeline? If yes, you can go to any store and buy a "branded" model (not equipped with Beeline firmware).

    That is, you can safely buy a router that is compatible with customized equipment. But this is not the only option. There are many models of routers that work "without problems" with one or another operator. Information about them can be found on the forums. And, let’s just say, it’s easier to choose a more “powerful” router among those that are not customized (it’s clear why: the operator should not sell too expensive devices).

    It is known that this list was significantly reduced in early 2013 (but still, there are 8 different routers here). Routers recommended by Beeline - can be configured to connect to this provider in 100% of cases (however, this is true for many other models). Beeline operator is obliged to provide free help in the router settings that are on the list.

    But in the past, this list was longer. The logic seems to be clear: why once again “upload” your service center? In general, if free "support" is not needed, the above list can be ignored. And buy and independently configure another device, router or access point.

    If you ask: which routers are suitable for Beeline, then the answer sounds like this - any that support "L2TP".

    The common problem here is:

    • The equipment can not cope with the work on the protocol "L2TP"
    • Connection "via L2TP" - you can create, while the address of the VPN server has to be specified in "digital" form (and not in the form of a server name)
    • You can’t configure IPTV (or - it’s possible for a “set-top box”, it’s impossible for a PC)

    Note that the second option is quite common. What can be considered a "minus", and not only when connecting to Beeline. The choice is up to the user.

    Setting the IPTV option (DIR-300NRU)

    Setting up a Beeline D150L WiFi router for viewing IPTV comes down to choosing a subscriber (set-top box / computer). Consider how you can enable this option in the D-Link DIR-300NRU router.

    As mentioned in the connection setup chapter, to enable IPTV, you must check the IGMP checkbox. Moreover, this should be done only when establishing a connection via IPoE (but not L2TP).

    In addition, in the web interface, go to the "Advanced" -> "IGMP" tab, and check the "Enabled" and "version 2" checkboxes here:

    IGMP setup

    By clicking "Change", then - saving the settings, you can watch IPTV on your computer. On a customized Beeline router, the instruction does not contain anything like this, and the setup looks much simpler.

    You can watch TV both through a computer and through a set-top box (which is true for the DIR-300NRU as well). But the setting in the D-Link interface for the latter case, for the set-top box, will be more difficult, and we will not consider this option here.

    The latter is in no way a "campaign" for the purchase of Beeline routers. Same as "against". D-Link, having released a router, provides support and updates firmware (moreover, more often than a “competitor” in the form mobile operator). The choice is again left to the user.

    On the Beeline WiFi router, the reviews tell us that the “simple” IPTV setup justifies itself, the option really works. We will notice: in Beeline.ru networks. Although, in theory, this will be the case in other networks (if multicast packets are used for IPTV transmission), but this, again, is only a theory.

    Common to all Beeline routers

    On the official website of the provider in open access There is a program called "Setup Wizard". The downside is that you need to run the program under Windows (2000 with the latest service pack, XP, and so on). The advantage is that even an inexperienced user can “cope” with the settings:

    Setup Wizard program

    The list of Beeline routers that are fully compatible with the program contains models offered by the operator (all without exception). In addition, you need to add DIR300A / C1 from D-Link and TRENDnet model 432BRP D2.0 here (if someone needs it). The list will grow over time.

    According to the set of functions, the program allows you to configure options that are displayed by the start tab GUI. In addition, here you can turn off Wi-Fi encryption. That is, the user can end up with a fully configured device with a wireless network and IPTV function. Looks like you can even customize local network(DHCP server).

    In any case, the Internet router supplied by Beeline can be configured to connect, both from the web interface and using the program. Last option– provided specifically as a “custom” one.

    Using this program - simplifies the configuration of the router. However, not so much. In any case, a device equipped with Ethernet ports will have to be connected to a computer (moreover, using network cable). Network Card computer must be configured correctly, and the router settings must be "default". If the latter is not observed, the program can detect the router “on its own” (though not always either).

    The setup looks much easier when a Beeline mobile router is connected to a computer via USB. For USB devices such as Cell Phones, smartphones and routers, a typical option is to install the program under Windows and configure the device. The program installer is stored on the built-in "hard drive", defined by any OS as a "USB flash drive".

    Maybe something similar will appear in "regular" routers, if we talk about customized firmware.

    Question answer

    Question: tell us more about Beeline TV, and what is better to use with it, a set-top box or a computer?

    If the subscriber does not use Beeline services as an Internet provider, you can watch TV through the set-top box. Otherwise, the same is available, plus several channels for viewing on a computer (use VLC or IPTV-player).

    Question: how to set up a Beeline WiFi router if you can’t open the web interface?

    Most likely, someone “already set up” such a router. You need to do a reset. Why, after turning on the power and waiting 1 minute, press the reset button. It is necessary to hold reset for 10-15 seconds (but no more), then release it. The router will be ready to work in 30 seconds.

    Question: Is it difficult to use a router with custom firmware by switching to another provider?

    In the considered device models, as we have seen, the firmware version modified “for Beeline” does not lose its functionality. WiFi setup Beeline router in this case will not differ from that for the device that is the "prototype" (D150L -> Dir 300 NRU, etc.).

    The video shows how to set up DIR-300NRU (B5 revision) for Beeline:

    The Tp-link router is very simple to set up, and also perfectly suited to the Beeline provider, this article will fully describe the configuration of the Tp-link router for Beeline with all its flaws, since all routers have minor flaws. Let's get started.

    Setting up the Internet on the router.

    First we need to go to the web interface of the router, for this we need to enter in address bar browser ip address of the router, in our case, on Tp-link routers, the default address is 192.168.0.1.

    After you try to go to this address, you will need to enter your login and password, if the router is new, then the login, the default password in it (admin login, admin password), if the logins and passwords do not match, try to reset the router to standard settings. After you have entered the web interface of the router, you need to go to the network tab, then select WAN.

    Here we need to change the connection type to L2TP Russia, (marked in the picture at number 1), after which you need to enter your logins and password for accessing the Internet (2), whether you configure the tp-router will depend on the correctness of the entered logins and passwords. link under Beeline or not. Next, we need to register the ip address, or server name (3), for Moscow it is tp.internet.beeline.ru. This completes the configuration of the tp-link router. We need to specify the MTU size (for Beeline 1400), after which we need to specify the maximum idle time, in our case 0, because if you do not change it to 0, then every 15 minutes of idle time the router will disconnect. After you have entered all the settings of the tp-link router under Beeline, you need to save them, after which the Internet should work.

    Wi-Fi setup, security.

    In order to set a password for the network, you need to go to the wireless mode tab, then select settings wireless mode Let's get started with the settings. The network name is how (5) your wireless network will be called (you can call it whatever you want),

    in the region field, select the United States, since the Wi-Fi power potential will be lower if you select Russia. Many people have problems connecting ipad 2 with these routers, in order for the tp-link router settings for Beeline to work correctly, you must select a channel width of 20 MHz (6), and then save all the settings you entered. Let's move on to setting up network security. We need the wireless security tab in it, you need to select the type of encryption WPA-PSK / WPA2-PSK (Recommended),

    in the password field, we will need to enter a password that you will not forget, since this password will need to be entered to connect to your Wi-Fi network. In the Group key renewal period field, enter the value 3600, and then save all the settings you have made.

    Setting up television on a tp-link beeline router.

    If you have television, then it will also need to be registered, configured on the router, for this we go to the network tab, then we need the IP-TV tab.

    In it, you need to select the bridge mode and indicate on which port the set-top box is connected to the router, then save all the settings and, for complete certainty, restart the router. This completes the configuration of the Tp-link router for Beeline.

    TP-Link specializes in the production and supply of network equipment in order to create wireless communication at home. Vendor models support any data transfer protocols regardless of the provider.

    Consider, using the Beeline company as an example, setting up a TP-Link router, which is carried out in several stages.

    To set the Internet connection parameters on the TP-link router, open the "Control Panel" through the web interface. By default, the username and password for logging in is admin. The main menu of the device will be displayed on the user's monitor.

    The advantage of the TP manufacturer's models is a single interface. The subscriber uses the instructions below for most solutions from the vendor.

    Next, let's figure out how to set up access to the "global network" from the Beeline provider using the example of TP-WR841ND V10. Detailed description of this model, as well as its configuration for other communication providers, are published on our website.

    After logging in through the browser to the "Control Panel" of the equipment, select Network / "Network", then - WAN:

    To configure the TP-Link router for the Beeline provider, we make the following settings:

    1. Connection type - Russia L2TP.
    2. Credentials are provided by the Internet service provider after the conclusion of the contract.
    3. In the field "IP-address of the server" we write: tp.internet.beeline.ru.
    4. We leave the item responsible for the IP address of the equipment as Auto.
    5. The connection mode is "Automatic".

    The screenshot below shows the configuration for Beeline in English:

    After the changes are made, click the Save / "Save" button, reboot the network equipment.

    On this initial setup Internet on the TP-Link router for Beeline is completed. Now for the additional options.

    Setting up a Wi-Fi network

    Setting router D- Link Dir-615 for provider " Beeline": preparation ... In line routers manufacturer D- Link router stands out ... On the new page in the connection type column, indicate "L2 TP + Dynamic IP" from the proposed list. Entering the username (login) and password (with...